RV Trip Planning Discussions

Go Back   iRV2 Forums > Blogs
Click Here to Login
Join iRV2 Today

Mission Statement: Supporting thoughtful exchange of knowledge, values and experience among RV enthusiasts.
Old

Fiberglass panel coming loose near entry door FIXED

Posted 05-18-2016 at 02:18 PM by ByeTheWay

Pleased with the results
Attached Thumbnails
Click image for larger version

Name:	DSC_9243.jpg
Views:	277
Size:	122.8 KB
ID:	446   Click image for larger version

Name:	DSC_9244.jpg
Views:	252
Size:	124.7 KB
ID:	447  

Senior Member
Posted in Uncategorized
Views 735 Comments 0 ByeTheWay is offline Edit Tags
Old

Workbench in the Basement

Posted 05-08-2016 at 04:40 PM by ByeTheWay

I sure got tired of working on small RV projects on the ground. So I made this 3/4” plywood storage box, for storage and a workbench. Instead of hinges, I made the top removable. The top stays in alignment with cleats on the underside. It took a little trail and error to allow for clearance. For strength I used cleats and lots of Gorilla Glue. My tool box fits neatly on the side. I’m 6’3” and the workbench is made to fit me.
Attached Thumbnails
Click image for larger version

Name:	DSC_9217.jpg
Views:	192
Size:	214.5 KB
ID:	444  
Senior Member
Posted in Uncategorized
Views 668 Comments 0 ByeTheWay is offline Edit Tags
Old

Between the Rail Storage

Posted 05-08-2016 at 04:04 PM by ByeTheWay

After trying to retrieve an item from my “Between the Rail Storage” and not being able to see what I was looking for I replaced the 1/2” plywood shelves with wire closet shelving. I fastened two pieces together using hog rings for strength and to give me a lip on each side. I found it easier to install each piece separately, then fasten them together.

Sure makes it easier to find what you are looking for when you can see it from below.
Attached Thumbnails
Click image for larger version

Name:	DSC_9238.jpg
Views:	225
Size:	254.7 KB
ID:	442   Click image for larger version

Name:	DSC_9242.jpg
Views:	207
Size:	301.2 KB
ID:	443  

Senior Member
Posted in Uncategorized
Views 989 Comments 2 ByeTheWay is offline Edit Tags
Old

Boondock Water Saver

Posted 05-05-2016 at 10:12 PM by ByeTheWay

As any Boondocker knows, water is precious. I have always had the desire to save the water that is normally wasted waiting for the shower water to warm up. I use to save it in a container, but that took extra effort so I looked for an easier solution.

I added a diverter valve and a shut off valve between the shower head and the shower supply pipe. This gives me the ability to divert the water to a separate line and also allows me to stop the flow of water all together without adjusting...
Attached Thumbnails
Click image for larger version

Name:	DSC_9197.jpg
Views:	199
Size:	144.4 KB
ID:	439   Click image for larger version

Name:	DSC_9198.jpg
Views:	215
Size:	116.9 KB
ID:	440  

Click image for larger version

Name:	DSC_9200.jpg
Views:	182
Size:	121.2 KB
ID:	441  
Senior Member
Posted in Uncategorized
Views 954 Comments 0 ByeTheWay is offline Edit Tags
Old

Aligning Bedroom TV with Bed

Posted 05-05-2016 at 09:40 PM by ByeTheWay
Updated 07-31-2018 at 10:07 PM by ByeTheWay

Our original Bedroom TV was located in the corner, above the washer/dryer. Watching it was uncomfortable because of the angle between the TV and the bed. I wanted to replace the old TV with an LED. My wife said can’t you line it up with the bed. After some thought I came up with my solution.

First I built a frame to match the existing cabinets. I then mounted a piece of 1/8” aluminum (painted black) to the back of the frame, which added strength to the frame. I installed the...
Attached Thumbnails
Click image for larger version

Name:	DSC_9232.jpg
Views:	191
Size:	244.6 KB
ID:	437   Click image for larger version

Name:	DSC_9206.jpg
Views:	227
Size:	164.4 KB
ID:	438  

Senior Member
Posted in Uncategorized
Views 1139 Comments 2 ByeTheWay is offline Edit Tags
Old

Fiberglass panel coming loose near entry door

Posted 05-04-2016 at 10:28 PM by ByeTheWay
Updated 05-04-2016 at 10:32 PM by ByeTheWay

As you can see, the fiberglass panel is coming apart at the seam. I tried a screw to keep it in place but it loosened, so I decided a bolt with a stop nut was a better idea. I got behind the screw that is suppose to keep everything in place. Directly behind the panel hole is a 1" x 1" or larger square steel tube, welded to the sub structure for the front end.
With the nose pulled out (like for Gen Service) I found a sheet of horizontal thin aluminum, covering access to the area...
Attached Thumbnails
Click image for larger version

Name:	DSC_9179 copy.jpg
Views:	213
Size:	83.7 KB
ID:	434   Click image for larger version

Name:	DSC_9182 copy.jpg
Views:	210
Size:	138.5 KB
ID:	435  

Senior Member
Posted in Uncategorized
Views 838 Comments 0 ByeTheWay is offline Edit Tags
» Featured Campgrounds

Reviews provided by


Copyright 2002- Social Knowledge, LLC All Rights Reserved.

All times are GMT -6. The time now is 05:27 AM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
×