C7 Fuel Filters Change

[The Sunde's]

We have a 06 Journey 39K with a Cat C7 and will be getting the fuel filters changed. Does anyone know if you have to pop the Engine Compartment top to change any of the filters? If so I will remove the bed and get it ready before hand.

[CWHTRAINS]

On my 06 Journey 36G the 2 micron fuel filter mounted on the engine itself was easier to get to with the engine cover located under the bed removed. Also, the 30 micron fuel/water separator filter located behind the rear radiator is easier to remove and replace if you take out the 6 or so screws holding in the lower rear engine loover (grate cover) as well.

[The Sunde's]

Thanks for the info, I will take advantage of your experience and remove the
mattress and hopefully make it easier for the tech doing the work. I'm to lazy and to old and to dumb to do it myself..

Thanks again,
Dick

[Sammie]

Your tech will thank you for making his job easier. Also before you take it in to be serviced, now would be a good time to wash off the engine. Use two cans of Gunk engine cleaner and then hose off the dirt. Let the engine dry before starting.

Sammie

[The Sunde's]

Point well made, I shall take your advise as no doubt that will be the time
to do it..

Happy travels
DicK

[cbeierl]

Here's an earlier thread about relocating the secondary filter to make it more easily accessible: Relocated Fuel Filter & Added Priming Pump .

[The Sunde's]

Chris, excellent idea, I will copy your idea and have that done. It seems like the aftermarket ideas would best be served in the original construction. Oh well this keeps us all thinking all the time.

Remember, "If you want a job done easy, find a lazy man he will always find a easy way to get the job done".

[wagonmaster2]

On my 2004 Meridian 36G it only takes raising the foot of the bed up, removing the 4 bolts holding the engine cover plate on, lifting or removing that engine cover, and there is the engine with the fuel filter located on the passenger side of the engine. Kind of takes standing on your head to reach the filter but not that difficult. All this might take 10 minutes unless the tech takes a lot of time finding his wrench. Then another 10 minutes to unscrew the old filter and replace the new one. I've done this myself a couple of times and also replaced the fuel/water filter back by the radiator, which is even easier. I just reach through the rear louvers, unscrew the old filter, change the clear bowl on the bottom to the new filter and replace the filter.

Don't know how much difference there might be between a 36 and 39 but hopefully this info will help some.

Wagonmaster2
2004 Meridian 36G

[The Sunde's]

What a wealth of information, thanks to all of you for your input.

The Sunde's

[Chief]

As wagonmaster has indicated above, no need to remove the bed, just clean out the compartment under the bed so the tech can get to the service panel.

[Old Snipe]

I have a 39K and you DO NOT have to remove the bed!!!

The panel to the rear of the bed and in front of the closet is the location for the access panel to the top of the engine.

To remove, you have to find two sets of two screws just under the lip of rug covered panel, (or top step if you wish to call it that). One set is a couple of inches from the end that abutts the closet, the second set is about 10 inches further around. You may have to poke around a bit because the screws may be buried in the carpet pile.

After you've removed the screws, get two long screwdrivers and work the rug covered panel up from the corner that is on the driver side rear. Using the two screwdrivers, the panel will lift slowly and you work around, lift the panel up from the closet side until it is a couple of inches up and then wiggle/slide it out towards the passenger side. It is a very hard process, the panel it a very tight fit, but with a little patience, it will come out.

Lift off the panel and you'll see it covers an black metal panel held down by about 6-8 bolts. Remove these bolts and this panel will lift off exposing the top of the engine and the filter. While this is off, go ahead and lube the exhaust brake with exhaust brake lube available from Camping World and problably other good RV dealers.

You reverse the process and will have a fight to get the rug covered panel back in place. It is so tight, I left out the hold down screws, can't see it falling out. I have heard that if you take a dremel tool and cut a groove down the underside of the rug panel (from driver's side topassenger's side)you can fold the panel enough to make removal easier. I'm going to look into that.

Please note that all the good folks that replied have the 36G floorplan that does indeed have the access under the bed, but the 39K does not. I don't want to see you remove your bed for no reason.

Best Regards!

[The Sunde's]

Paul, thanks for the information. It sounds like you may have saved me a or two. I will tackle that one tomorrow. Thanks again, it's much appreciated.

[Old Snipe]

That's what we're all here for, to help each other out.

If you have any other questions, give me a shout or a PM, I'll talk you through it.

Best Regards!

[cbeierl]

Here are a couple of pictures of my two shutoff valves. They're accessed from underneath from the driver's side below/beside the engine.