 |
03-04-2007, 11:39 AM
|
#1
|
|
Senior Member
Winnebago Owners Club
Join Date: Jul 2004
Location: winter:Congress,AZ summer: on the road.
Posts: 108
|
Does anyone know where (exactly) the level sensing unit on my rig is located? Mine is stuck in the left front down position and will not change. Can jack the rig all over the place and the lights do not change. Help!
__________________
04 Meridian 34H
2010 Honda CRV / M&G Braking
|
|
|
|
| |
|
 |
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
|
03-04-2007, 11:39 AM
|
#2
|
|
Senior Member
Winnebago Owners Club
Join Date: Jul 2004
Location: winter:Congress,AZ summer: on the road.
Posts: 108
|
Does anyone know where (exactly) the level sensing unit on my rig is located? Mine is stuck in the left front down position and will not change. Can jack the rig all over the place and the lights do not change. Help!
__________________
04 Meridian 34H
2010 Honda CRV / M&G Braking
|
|
|
|
| |
|
|
03-04-2007, 11:41 AM
|
#3
|
|
Senior Member
Join Date: Aug 2002
Location: Murfreesboro TN
Posts: 144
|
Are you referring to the jack down sensor, or the level sensor?
Sounds like you are asking about the jack down sensor, it is located at the top of the individual jack.
__________________
Chris McVetty
Murfreesboro TN
|
|
|
|
| |
|
|
03-04-2007, 11:44 AM
|
#4
|
|
Senior Member
Winnebago Owners Club
Join Date: Jul 2004
Location: winter:Congress,AZ summer: on the road.
Posts: 108
|
I looking for the level sensor, a 4 inch disk "usually mounted on the under side of the coach to wards the middle of the coach" or so the book says.
__________________
04 Meridian 34H
2010 Honda CRV / M&G Braking
|
|
|
|
| |
|
|
03-04-2007, 11:57 AM
|
#5
|
|
Senior Member
Join Date: Aug 2002
Location: Murfreesboro TN
Posts: 144
|
Sorry, not sure about that. In mine the level sensing device is in the HWH control box, but your rig is likely significantly different than mine.
__________________
Chris McVetty
Murfreesboro TN
|
|
|
|
| |
|
|
03-04-2007, 01:21 PM
|
#6
|
|
Senior Member
Winnebago Owners Club
Join Date: Jul 2004
Location: winter:Congress,AZ summer: on the road.
Posts: 108
|
Bingo Chris, Mine is in the control box also!!Output does not change with position, guess I get to call HWH tomorrow. I remember they were pretty good to work with. Wish me luck. Thanks for the help Chris.
__________________
04 Meridian 34H
2010 Honda CRV / M&G Braking
|
|
|
|
| |
|
|
03-04-2007, 01:45 PM
|
#7
|
|
Senior Member
Winnebago Owners Club
Join Date: Jun 2004
Location: SW Florida
Posts: 880
|
bill j - Mine failed last year. Luckily, while still under warranty - can't remember now whether warranty was an issue or not. I know they just shipped me a new level sensor board and I had to return the old one. It's not much trouble to change out. I did it from underneath without removing the control box (that would be a PIA cause there's a bunch of cables to be disconnected). As I remember, you just roll back the rubber collar around the clear faceplate and the faceplate comes off. Changing out the pc board/sensor was simple. I had more trouble getting that rubber collar properly replaced than anything else. Good Luck...
__________________
Tom
'04 Journey 36G - Cat C7
'04 Honda CR-V
|
|
|
|
| |
|
|
03-04-2007, 01:57 PM
|
#8
|
|
Senior Member
Winnebago Owners Club
Join Date: Jul 2004
Location: winter:Congress,AZ summer: on the road.
Posts: 108
|
Yes Tom, I removed the clear cover to check the board out. How does the sensor board come out? I'm not going back under there tonight. Just got back from boon-docking this afternoon and that's when it failed. Tomorrow's another day, ain't Rv'ing fun? Thanks for the info.
__________________
04 Meridian 34H
2010 Honda CRV / M&G Braking
|
|
|
|
| |
|
|
03-04-2007, 02:09 PM
|
#9
|
|
Senior Member
Winnebago Owners Club
Join Date: Jun 2004
Location: SW Florida
Posts: 880
|
Sorry, Bill, I can't remember (CRS) what was involved in changing the board. I just know I'm not too handy and, if it had been hard, I would've remembered. I do remember messing with that rubber collar for 10 or 15 minutes trying to get it right.
__________________
Tom
'04 Journey 36G - Cat C7
'04 Honda CR-V
|
|
|
|
| |
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
|
| Thread Tools |
Search this Thread |
|
|
|
| Display Modes |
 Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
»
Recent Discussions
»
Upcoming Rallies
No events scheduled in
the next 365 days.
|
»
iRV2 on facebook
|
Copyright 2002-2012 Social Knowledge, LLC All Rights Reserved.
All times are GMT -6. The time now is 10:55 AM.
Chevy Camaro Forum
Ford Mustang Forum
Jeep Wrangler Forum
Volkswagen Touareg Forum
Land Rover Defender Forum
