RV Trip Planning Discussions

Go Back   iRV2 Forums > THE OWNER'S CORNER FORUMS > Winnebago Industries Owner's Forum
Click Here to Login
Join iRV2 Today

Mission Statement: Supporting thoughtful exchange of knowledge, values and experience among RV enthusiasts.
Reply
  This discussion is proudly sponsored by:
Please support our sponsors and let them know you heard about their products on iRV2
 
Thread Tools Search this Thread Display Modes
 
Old 09-18-2008, 08:42 AM   #1
Junior Member
 
Join Date: Sep 2008
Posts: 2
I have a 1997 Winnebago Vectra 36WQ (Ford Chasis) that I just got a new key fob for. I tried the standard Ford programming (Turning on/off ignition switch 8x, but it didn't work - any ideas or suggestions?

Thanks,

Craig
__________________

Coltpeyt is offline   Reply With Quote
Join the #1 RV Forum Today - It's Totally Free!

iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!

You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!

Old 09-18-2008, 08:42 AM   #2
Junior Member
 
Join Date: Sep 2008
Posts: 2
I have a 1997 Winnebago Vectra 36WQ (Ford Chasis) that I just got a new key fob for. I tried the standard Ford programming (Turning on/off ignition switch 8x, but it didn't work - any ideas or suggestions?

Thanks,

Craig
__________________

Coltpeyt is offline   Reply With Quote
Old 09-21-2008, 05:55 PM   #3
Senior Member
 
Join Date: Nov 2006
Location: Grayson, GA
Posts: 897
I don't know if this will help you or not but this is the way the fobs are
re-programed on a 97 Ford F250HD.

Read first and then look for the
module and the program connector.

You have to have all of your fobs present as when you enter the programming
mode, it will erase all from memory.

You are also going to have to locate the module (remote entry receiver
module) I referred to above and the program connector. The remote entry
receiver module is located in the LH side of the lower instrument panel to
the right of the steering column, just above the driver's right foot area.

Read this in total and then see if it will work for you.

NOTE: The remote entry receiver module erases all previous transmitters from
memory when the transmitters are programmed or reprogrammed. The remote
entry receiver module can store up to four transmitters in memory.

To program (or reprogram) transmitter(s) into the remote entry receiver
module, perform the following steps:

Turn key to the ON or ON/ACCESSORY position and momentarily short the two
terminals of the program connector (C4) (a two-pin connector taped to the
wire assembly connected to the remote entry receiver module, approximately 6
inches from the remote entry receiver module). All doors should lock then
unlock. Remove shorting pin.

Press any button on transmitter. All doors should lock then unlock to verify
that the transmitter has been programmed. If door locks do not respond,
press button again (up to three times maximum with the same transmitter).

Repeat Step 2 to program additional transmitters into the remote entry
receiver module (up to four transmitters maximum).

Key off. All doors should lock then unlock.

Check operation.
__________________
Dave and Karen -- '02 Ultimate Advantage 36 C, 350 HP Cummins, Allison 3060 Tranny, 2013 Ford Edge, InvisiBrake
David K is offline   Reply With Quote
Reply



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
TriMark key FOB programming? nodine Monaco Owner's Forum 16 01-20-2017 09:00 PM
Keyless Entry Programming Halbrooks Winnebago Industries Owner's Forum 4 08-20-2007 04:33 PM
Cingular Wireless to AT&T Wireless ChiefJohn Technology: Internet, TV, Satellite, Cell Phones, etc. 3 12-29-2006 02:05 PM
CAT C7 ECU programming Motorhome05 Winnebago Industries Owner's Forum 4 12-15-2005 02:09 PM
EC-30 Programming Dr Tate Winnebago Industries Owner's Forum 5 11-29-2005 02:21 PM

» Featured Campgrounds

Reviews provided by


Copyright 2002- Social Knowledge, LLC All Rights Reserved.

All times are GMT -6. The time now is 10:36 PM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
×