|
|
08-08-2019, 02:47 PM
|
#1
|
Senior Member
Join Date: Dec 2018
Location: OC, CA
Posts: 151
|
Full wall slide front bottom corner sticking out
I pulled the full wall slide in today and the front bottom corner is out about 1/2 inch. Newmar told me to check the HWH fluid and said it was located in the front next to the generator. I couldn't find it there. Any suggestions? How do you adjust this?
Thanks, Jared
__________________
Jared and Ruby
2019 Dutch Star 4018, 2019 Honda Fit
OC, CA
|
|
|
|
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
08-08-2019, 03:57 PM
|
#2
|
Senior Member
Newmar Owners Club Spartan Chassis
Join Date: Aug 2018
Location: Knoxville, TN
Posts: 260
|
Facing the gen it’s on the left side. Pull your gen out and it’s easier to get to
It looks like something is wrong with the fit. You’re trim appears broke
__________________
Bill & Mary
2023 Renegade Valencia 38RB on order
2019 Jeep Cherokee Overland (Sold 2019 Newmar DS 4369)
|
|
|
08-08-2019, 04:21 PM
|
#3
|
Senior Member
Join Date: Dec 2018
Location: OC, CA
Posts: 151
|
Quote:
Originally Posted by Boilervol
Facing the gen it’s on the left side. Pull your gen out and it’s easier to get to
It looks like something is wrong with the fit. You’re trim appears broke
|
Ok I can see your reservoir and I'm guessing the white knob is for filling. You also have a tray that holds the reservoir and the HWH unit. Take a look at my photo. And see if that looks right to you. I don't have that tray and something brown appears to be covering the reservoir. I will have to take another look tomorrow. No broken trim piece. The slide is just sticking out about 1/2". Not sure why my photos are off by 90 degrees.
__________________
Jared and Ruby
2019 Dutch Star 4018, 2019 Honda Fit
OC, CA
|
|
|
08-08-2019, 04:32 PM
|
#4
|
Senior Member
Newmar Owners Club Spartan Chassis
Join Date: Aug 2018
Location: Knoxville, TN
Posts: 260
|
Yes , the white cap is for filling. Both our coaches are 2019 so I’m surprised there is a difference. Maybe someone with a 2019 - 4018 can chime in.
__________________
Bill & Mary
2023 Renegade Valencia 38RB on order
2019 Jeep Cherokee Overland (Sold 2019 Newmar DS 4369)
|
|
|
08-08-2019, 05:37 PM
|
#5
|
Moderator Emeritus
Nor'easters Club Workhorse Chassis Owner iRV2 No Limits Club
Join Date: Oct 2004
Posts: 30,785
|
The bell vents for filling are removed and the shaft will have two lines and you fill to between them.
All your jacks need to be retracted before filling and do not over fill.
You have to turn your phone to horizontal to get correct picture.
Make sure the reveal is good around your FWS after re leveling coach before deploying the slide.
Slide information in this link.
Read this link before deploying your FWS slide.
|
|
|
08-08-2019, 06:03 PM
|
#6
|
Junior Member
Join Date: Jan 2019
Posts: 9
|
Your fluid is probably not low.
Try bleeding your cylinder solenoids.
There is a small white paddle on the back of each solenoid. Move it and you will hear a hiss if there is air in the system. Then cycle the slide out and back in.
|
|
|
08-08-2019, 06:13 PM
|
#7
|
Moderator Emeritus
Nor'easters Club Workhorse Chassis Owner iRV2 No Limits Club
Join Date: Oct 2004
Posts: 30,785
|
Thanks for that advise Knoxious will be using in the new slide thread I'am writing up.
It will be placed in this thread.
If you have any more pictures and thoughts on FWS I can use them on that need your help thread.
Welcome to the forum also.
|
|
|
08-08-2019, 06:52 PM
|
#8
|
Senior Member
Newmar Owners Club Spartan Chassis
Join Date: Oct 2014
Location: Lake McClure, CA
Posts: 1,449
|
Is it just the bottom corner ? Looks like the left side is sticking out.
__________________
2018 Dutch Star 4369 Spartan Chassis
2016 Jeep Cherokee, 1952 Willys CJ3A
|
|
|
08-08-2019, 10:54 PM
|
#9
|
Senior Member
Join Date: Dec 2018
Location: OC, CA
Posts: 151
|
Quote:
Originally Posted by 10 fan
Is it just the bottom corner ? Looks like the left side is sticking out.
|
As you go up it gets closer and no gap towards the top.
__________________
Jared and Ruby
2019 Dutch Star 4018, 2019 Honda Fit
OC, CA
|
|
|
08-08-2019, 10:56 PM
|
#10
|
Senior Member
Join Date: Dec 2018
Location: OC, CA
Posts: 151
|
Quote:
Originally Posted by Knoxious
Your fluid is probably not low.
Try bleeding your cylinder solenoids.
There is a small white paddle on the back of each solenoid. Move it and you will hear a hiss if there is air in the system. Then cycle the slide out and back in.
|
Should I do this while the slide is out? Or in and then do a complete cycle?
__________________
Jared and Ruby
2019 Dutch Star 4018, 2019 Honda Fit
OC, CA
|
|
|
08-09-2019, 08:07 AM
|
#11
|
Junior Member
Join Date: Dec 2018
Posts: 26
|
fws front bottom corner sticking out
as 007 posted the jacks need to be up but the fws needs to be out to check the fluid, while out the cylinder`s piston are in. adjustment is the 2 nuts on the bottom of the cylinder, if that is the problem. hope this helps Harlan
|
|
|
08-09-2019, 04:43 PM
|
#12
|
Senior Member
Join Date: Sep 2016
Location: Sarasota, FL
Posts: 5,228
|
Quote:
Originally Posted by DutchStar JK
Ok I can see your reservoir and I'm guessing the white knob is for filling. You also have a tray that holds the reservoir and the HWH unit. Take a look at my photo. And see if that looks right to you. I don't have that tray and something brown appears to be covering the reservoir. I will have to take another look tomorrow. No broken trim piece. The slide is just sticking out about 1/2". Not sure why my photos are off by 90 degrees.
|
Please hold your phone horizontal with the lens to the left. Otherwise it makes analyzing your problem tough. Please post new pics.
__________________
Rick and Larrie Dee
1997 40' Newmar London Aire DP CTA 8.3 (Mechanical) 325 Spartan MM
Bringing her back to her glory.
'08 Jeep GC Overland.
|
|
|
08-09-2019, 07:14 PM
|
#13
|
Member
Newmar Owners Club
Join Date: Sep 2006
Posts: 65
|
2019 DUTCHSTAR. I am having the exact same problem. The FWS is flush at top, and out about 1 inch at bottom. It seems to happen after it is sitting in storage for 24 hrs.
Where do I find the slide resevoir, and if I were to bleed the selenoids, where are they, and how many?
Thanks.
__________________
Traveler3
|
|
|
08-09-2019, 07:56 PM
|
#14
|
Moderator Emeritus
Nor'easters Club Workhorse Chassis Owner iRV2 No Limits Club
Join Date: Oct 2004
Posts: 30,785
|
Quote:
Originally Posted by webwalker
2019 DUTCHSTAR. I am having the exact same problem. The FWS is flush at top, and out about 1 inch at bottom. It seems to happen after it is sitting in storage for 24 hrs.
Where do I find the slide resevoir, and if I were to bleed the selenoids, where are they, and how many?
Thanks.
|
You should read whole thread the #6 post has your answer, you need the links in this post also.
|
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|