RV Trip Planning Discussions

Go Back   iRV2 Forums > THE OWNER'S CORNER FORUMS > Newmar Owner's Forum
Click Here to Login
Join iRV2 Today

Mission Statement: Supporting thoughtful exchange of knowledge, values and experience among RV enthusiasts.
Reply
  This discussion is proudly sponsored by:
Please support our sponsors and let them know you heard about their products on iRV2
 
Thread Tools Search this Thread Display Modes
 
Old 10-07-2007, 11:20 AM   #1
Junior Member
 
Join Date: Feb 2007
Posts: 24
I have a 2005 KS 3910 and the front of the dinning/living slide on the drivers side is coming out further than the back of it. Up front the rubber seal is pressed tight, but at the back by the fridge, I can stick my finger in there. Does anyone have a picture of what I need to adjust?
Thanks
Bill
__________________

__________________
03 KS 3904
Ultrastryk is offline   Reply With Quote
Join the #1 RV Forum Today - It's Totally Free!

iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!

You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!

Old 10-07-2007, 11:20 AM   #2
Junior Member
 
Join Date: Feb 2007
Posts: 24
I have a 2005 KS 3910 and the front of the dinning/living slide on the drivers side is coming out further than the back of it. Up front the rubber seal is pressed tight, but at the back by the fridge, I can stick my finger in there. Does anyone have a picture of what I need to adjust?
Thanks
Bill
__________________

__________________
03 KS 3904
Ultrastryk is offline   Reply With Quote
Old 10-08-2007, 05:34 AM   #3
Senior Member
 
Join Date: Apr 2007
Posts: 889
If there are threaded steel rods near either end of the slide (underneath), these are the adjusting/stop rods.
__________________
2016 Winnebago Grand Tour QL
2006 Hummer H2
Blue Ox/M&G
soricobob is offline   Reply With Quote
Old 10-13-2007, 05:53 AM   #4
Junior Member
 
Join Date: Feb 2007
Posts: 24
Mine does have those rods. Can someone tell me how to adustment?

Thanks
Bill
__________________
03 KS 3904
Ultrastryk is offline   Reply With Quote
Old 10-13-2007, 06:31 AM   #5
Senior Member
 
Oemtech's Avatar
 
Join Date: Feb 2003
Location: Jarrell, TX 76537
Posts: 4,368
Send a message via AIM to Oemtech
I got the following from Richard Bremen. He asked Newmar the same question.

<BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Locate the driveshaft under the slide room in the baggage compartments.
Follow the shaft from the cogs that drive the room to a cup, trans torque
bushing. Those are the side to side adjustment points. With the room
approximately half way out take a measurement on each side of the room from
the same point on the sidewall to the same point on the slide room exterior
wall. Loosen one bushing 3 turns using a 1 1/2 inch wrench and tap on the
cup part with a hammer to loosen the wedge inside. Using a pipe wrench move
the side of the room (as needed) to make both sides even. Tighten the nut to
100 ft lb (tight) while holding the shaft with the pipe wrench.
If you need to call for assistance, Mon-Fri 7:30 am to 4:00 pm EST
1-800-731-8300. </div></BLOCKQUOTE>
__________________
Dale
AKA - Oemy
Oemtech is offline   Reply With Quote
Old 11-11-2007, 04:37 AM   #6
Junior Member
 
Join Date: Oct 2007
Posts: 16
<BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by soricobob:
If there are threaded steel rods near either end of the slide (underneath), these are the adjusting/stop rods. </div></BLOCKQUOTE>

If you have locking bars, use them they will square it up.
Good luck, Rich
Rich Novak is offline   Reply With Quote
Old 11-11-2007, 04:31 PM   #7
Community Moderator
 
"007"'s Avatar


 
Nor'easters Club
Workhorse Chassis Owner
iRV2 No Limits Club
Join Date: Oct 2004
Posts: 29,664
Bill if you would go to QUICK TIPS AND EASY MODS just above there are links with pics to help you out. They show stop nuts and what to adjust.
__________________

__________________
98KSCA, 99MACA, 03 KSCA-3740- 8.1 Chev-- ALLISON Trans
VISIT the NEWMAR QUICK TIPS & EASYMODS 1 & 2
QUICK TIPS # 3
RV SYSTEMS & APPLIANCES & RECALLS --- TECH INFORMATION
"007" is offline   Reply With Quote
Reply



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Kountry Star Galena Newmar Owner's Forum 5 10-26-2007 05:27 AM
Kountry Star vs. Dutch Star John95683 Newmar Owner's Forum 6 06-21-2007 03:47 PM
Kountry Star Ed-Deb Newmar Owner's Forum 24 06-13-2006 07:58 AM
New Kountry Star trs Newmar Owner's Forum 19 04-29-2006 06:05 AM
Kountry Star DP or Dutch Star DP kissimmeekid Newmar Owner's Forum 6 12-21-2005 04:44 PM

» Featured Campgrounds

Reviews provided by


Copyright 2002- Social Knowledge, LLC All Rights Reserved.

All times are GMT -6. The time now is 03:38 AM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2019, vBulletin Solutions, Inc.