RV Trip Planning Discussions

Go Back   iRV2 Forums > THE OWNER'S CORNER FORUMS > Alpine Coach Owner's Forum
Click Here to Login
Join iRV2 Today

Mission Statement: Supporting thoughtful exchange of knowledge, values and experience among RV enthusiasts.
Thread Tools Search this Thread Display Modes
Old 07-31-2011, 07:53 AM   #1
Alpine Owners Club
Join Date: Dec 2008
Posts: 65
Grease fitting checklist

Hey everyone, trying to finish up with my maintainence and was hopping someone might have a list of the chassis / drive train grease fittings. After searching through the treads I didn't see anything. Also, what grease do you recommend?

Greg Michel
2001 Alpine 36MDS
Greg from Pittsburgh is offline   Reply With Quote
Join the #1 RV Forum Today - It's Totally Free!

iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!

You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!

Old 07-31-2011, 01:12 PM   #2
Senior Member
Dave Fernandez's Avatar
Alpine Owners Club
Join Date: Jun 2003
Location: Ontario, CA USA
Posts: 1,314
Hello Greg:

For a 2001 Alpine you will find the following grease fitting.

Under the Coach on the Steering Colum there is one on the slip yoke and one in the small u-joint. On the break peddle assembly you will find one the pivot shaft. The drag Ling and tie Rod have grease fitting on each end. The King Pins have Grease Fitting on the top and bottom. Thatís all for the front end.

In the Rear you have the Drive Shaft U-Joints have grease fitting (Each U-Joint is crossed drilled and they have two grease fittings you only need to grease one) and one on the slip yoke.

The Manual recommends that the Drive Shaft U-Joint be greased every 3000 miles (Which I Do) and the Chassis I perform once a year.

That the complete list of grease fitting on a 2001 Alpine.
Dave Fernandez
2001, 38ft FDDS, 350 ISC, Tow 2004 Yukon
Dave Fernandez is offline   Reply With Quote

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
Source for new grease fitting rubber boot? tmitchell Spartan Motorhome Chassis Forum 4 02-21-2010 08:08 PM
Zerk Fitting Grease Amounts Chief Freightliner Motorhome Chassis Forum 8 01-12-2009 12:14 PM
IMPROTANT: Zerk (grease fitting) Install in Brake Relay Rod? k1hog Workhorse and Chevrolet Chassis Motorhome Forum 48 02-12-2008 06:00 AM
Brake Grease Fitting adj Workhorse and Chevrolet Chassis Motorhome Forum 10 03-12-2007 07:54 PM
Grease fitting gunny Winnebago Industries Owner's Forum 12 02-05-2006 08:28 AM

» Featured Campgrounds

Reviews provided by

Copyright 2002- Social Knowledge, LLC All Rights Reserved.

All times are GMT -6. The time now is 11:29 AM.

Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2018, vBulletin Solutions, Inc.