|
|
10-19-2015, 02:06 PM
|
#15
|
Senior Member
Join Date: Nov 2005
Posts: 7,400
|
OK--I'll take a shot and try and answer a few of your questions. In no particular order: 1] WRV used headlight assemblies from the BMW 5-series auto, E39, 1997-2003, or there abouts for later Alpines. Accordingly, there are no WRV part numbers to look for--just BMW. There are a number of replacement options out on Amazon/Ebay. As you can imagine, OEM replacements for BMWs are pricey; after market ones, not so much. 2] Not a VANSCO expert but am of the opinion that automotive accessories are powered thru the front Vansco power unit, this could account for some low voltage issues--helps explain why using a direct feed from the bats with a relay might work better. 3] Fit and finish for either OEM or aftermarket assemblies is a modest challenge. The fiberglass opening and mounting tabs make it difficult to get either type of light to aim high enough. Might also note that on most Alpines, the fiberglass cap radius on the driver's side opening is very close to the shape of the light assembly; the passenger side is not as good--so some "fitting" is needed regardless. Final note: if you do shop for aftermaket lamps--eg Depot brand--these assemblies come with several "pigtail" options--apparently, BMW changed their wiring configs during the period. Biggest issue is the orange lights on the outside edges. The replacement lights I purchased came with a single element bulb/socket. Alpines use a two-filement bulb to combine running/marker and turn signal.....good luck
__________________
Old Scout
2015 IH45 Foretravel
2003 Alpine 40' MDTS [Sold]
New Braunfels, Texas
|
|
|
|
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
10-20-2015, 11:05 AM
|
#16
|
Senior Member
Alpine Owners Club
Join Date: Dec 2009
Location: Des Moines,Iowa
Posts: 241
|
Marvin,
If your existing headlight housings are in good shape with no haze or discoloration of the clear lens, you should be just fine as long as the adjustment screw has not been stripped or broken.
The trick is that the headlight housing needs to be re-positioned. You will need to remove the housing and grind away some fiberglass and slot the mounting holes. Like EM said, the issue is that WRV molded the front fascia so the lights fit nice and tight and look very nice. The problem is that they are aimed at the ground and the adjustment knob on the housings cannot be adjusted up far enough to point the beam of light down the road.
To get the light to point down the road, you need to tilt the headlamp housings back and to do that, you need to grind away some of the fiberglass around the headlights. (this is just based on my experience, YMMV) When you first do this you are going to find that the headlights will not be as smoothly integrated with the shape of the front of the coach. Nobody but you will never notice this after its done.
Over the years it seems like there is endless discussion about how to make the Alpine/BWM E39 headlights brighter. In most cases, THEY ARE PLENTY BRIGHT. You just can't tell because they are pointed at the ground.
Hope this helps.
__________________
Jeff
2001 Alpine 36MDDS
|
|
|
10-21-2015, 12:40 PM
|
#17
|
Senior Member
Join Date: May 2004
Location: Auburn, CA, Havasu, AZ & Mulege, BCS
Posts: 5,385
|
My experience (and Dale Gerstel's after a lot of effort) was that proper re-aiming of the lights actually produced a gap at the upper part of the headlight lens to the body of the coach.
IIWMI'd re-aim the "running lights" or fog lights upward (bend the bracket). To do this in a totally professional way you would also grind a bit off the lower round fiberglass cutout to push the bottom of the round lens forward against the new cutout profile. Then use the driving lights for proper wash of the road w/usable light after dark.
__________________
Baja-tested '08 2-slide 36'
Alpine: The Ultimate DIY'er Project
|
|
|
10-22-2015, 10:44 AM
|
#18
|
Senior Member
Join Date: Jun 2005
Posts: 1,957
|
I'll second using the driving lights. They work great even without adjustment. Mine seem to be adjusted pretty well to start with.
However I still prefer to stop well before dark!!
__________________
Jim A
'04 Alpine Coach 36' MDDS
|
|
|
10-22-2015, 10:56 AM
|
#19
|
Senior Member
Country Coach Owners Club Solo Rvers Club iRV2 No Limits Club
Join Date: May 2011
Location: Vancouver, WA
Posts: 37,725
|
On our totally different rig I replaced the bulbs with LED's. They have a separate "transformer" that must be wired in but all connections are already done. The hardest part was cutting out the rear cover for the cooling fan on the back of the new socket.
__________________
2009 45' Magna 630 w/Cummins ISX 650 HP/1950 Lbs Ft, HWH Active Air
Charter Good Sam Lifetime Member, FMCA,
RV'ing since 1957, NRA Benefactor Life, towing '21 Jeep JLU Rubicon Ecodiesel
|
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|