|
04-22-2008, 12:33 PM
|
#1
|
Senior Member
Workhorse Chassis Owner
Join Date: Feb 2005
Location: western wa.
Posts: 563
|
want to change out my rear tv. sits on cabinet in corner. seems to be atatched from undernieth but inside cabinet the panel is solid. don't see how to get to fasteners. any help please. thanks dave
__________________
2018 Jayco redhawk E 22
chevrolet express 4500 chassis
6LT
|
|
|
|
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
04-22-2008, 12:33 PM
|
#2
|
Senior Member
Workhorse Chassis Owner
Join Date: Feb 2005
Location: western wa.
Posts: 563
|
want to change out my rear tv. sits on cabinet in corner. seems to be atatched from undernieth but inside cabinet the panel is solid. don't see how to get to fasteners. any help please. thanks dave
__________________
2018 Jayco redhawk E 22
chevrolet express 4500 chassis
6LT
|
|
|
04-22-2008, 12:35 PM
|
#3
|
Senior Member
Workhorse Chassis Owner
Join Date: Feb 2005
Location: western wa.
Posts: 563
|
my dolphin is a 6342. thanks
__________________
2018 Jayco redhawk E 22
chevrolet express 4500 chassis
6LT
|
|
|
04-22-2008, 12:45 PM
|
#4
|
Senior Member
National RV Owners Club Workhorse Chassis Owner
Join Date: Jul 2006
Location: San Jose, Ca.
Posts: 1,334
|
That's odd. My rear TV sits on a bracket of sorts and the four screws are plainly visible but the rear ones are a little hard to get to. Got any pictures?
__________________
Rick and Julia
2005 Dolphin 5376, W24, Solid Body Paint, Koni FSD's
Looking for a new toad
|
|
|
04-23-2008, 06:50 PM
|
#5
|
Senior Member
Workhorse Chassis Owner
Join Date: Jan 2002
Location: Pacific Northwest or SoCal
Posts: 3,035
|
Like Rick was saying, normally the front plate is removed, then slide the TV forward. Watch-out the unit is a good 40 lbs.
Fred
__________________
Fred and Bonnie
2005 Dolphin LX 6375
Abby, Ruffles & Scarlett, "The Cats"
|
|
|
04-24-2008, 02:58 PM
|
#6
|
Senior Member
National RV Owners Club Ford Super Duty Owner
Join Date: May 2007
Location: El Cajon CA
Posts: 2,083
|
In my 07 Sea Breeze the bedroom TV in the corner has one screw going through the shelf over hang and into the bottom of the TV. It appears that the other screw is under the panel inside the cabinet below the TV. The panel must be removed or a one inch hole bored to get to it the screw head for removal. If you boar a hole it can be covered with a cap, It's out of sight only you will know its there.
Good Luck
__________________
2007 Sea Breeze LX 8321 Ford Chassis
2004 Ford Ranger Edge
El Cajon CA.
|
|
|
04-24-2008, 05:01 PM
|
#7
|
Senior Member
National RV Owners Club Workhorse Chassis Owner
Join Date: Jul 2006
Location: San Jose, Ca.
Posts: 1,334
|
Remove the screws you see and then try to pull or lift the tv up. If you think about it, could they of put in a screw where you think you need to bore a hole to get it out?
__________________
Rick and Julia
2005 Dolphin 5376, W24, Solid Body Paint, Koni FSD's
Looking for a new toad
|
|
|
04-24-2008, 05:51 PM
|
#8
|
Senior Member
Workhorse Chassis Owner
Join Date: Feb 2005
Location: western wa.
Posts: 563
|
no bracket n no visable screws. went in there today n removed (destroyed) roof panel inside cabinet. sure nuff there was a construction screw going up into tv. must be at least 4 maybe more. think i'll try the holesaw thing n then just glue the blank back in. hope the screws are all in the corners. thanks guys dave
__________________
2018 Jayco redhawk E 22
chevrolet express 4500 chassis
6LT
|
|
|
04-26-2008, 01:17 PM
|
#9
|
Senior Member
Workhorse Chassis Owner
Join Date: Feb 2005
Location: western wa.
Posts: 563
|
well, it's out and a good time was had by all. 2 screws in front and 2 metal straps in back. god did good when he invented the sawsall!! can't say as much for the joker that did the install. now in with the HD LCD. should be a walk in the park. hope it's a small park! thanks to all. dave
__________________
2018 Jayco redhawk E 22
chevrolet express 4500 chassis
6LT
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|