Join CruisersForum Today
Mission Statement: Supporting thoughtful exchange of knowledge, values and experience among RV enthusiasts.
Reply
 
Thread Tools Search this Thread Display Modes
Obd 2 port
Old 05-15-2011, 08:24 PM   #1
yardpass is offline
Junior Member
yardpass's Avatar
Join Date: Feb 2011
Posts: 14
Looking for the OBD 2 port on a 2006 Bounder 33R looked under dash and around engine compartment just do not see it does any one know where they hid it.

__________________
  Reply With Quote
   
Join the #1 RV Forum Today - It's Totally Free!

iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!

You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!

Old 05-15-2011, 09:22 PM   #2
goldwingerx2 is offline
Senior Member
goldwingerx2's Avatar
Winnebago Owners Club
Join Date: Aug 2009
Posts: 209
It might help if we knew the chassis that is on your MH.

__________________
Dean & Mary (Retired U.S.A.F.) plus Purr & Sparkles
12 Itasca Sunova 33C, 12 Smart w/Blue Ox setup, or tow dolly & 12 Prius
  Reply With Quote
   
Old 05-15-2011, 09:26 PM   #3
Jack R is offline
Senior Member
Jack R's Avatar


Tiffin Owners Club
Join Date: May 2009
Location: Lacey, Wa
Posts: 506
OBDII is located on fire wall within 8 - 10 inches of steering wheel. About 2" in length. Probably has a black cap over it.

jack
__________________
  Reply With Quote
   
Old 05-15-2011, 11:53 PM   #4
yardpass is offline
Junior Member
yardpass's Avatar
Join Date: Feb 2011
Posts: 14
Quote:
Originally Posted by goldwingerx2
It might help if we knew the chassis that is on your MH.
Ford chassis not sure of the number will have to check tomorrow
__________________
  Reply With Quote
   
Old 05-16-2011, 09:35 AM   #5
ga traveler is offline
Senior Member


Ford Super Duty Owner
Join Date: Dec 2009
Location: Mcdonough, Ga.
Posts: 1,387
Your chassis is a F53. The OBDll plug comes mounted on the steering column support on the right side of the steering wheel. It comes from the factory at this point. However, the factory leaves a two foot lead (wire) so the MH manuf. can move it if it is covered by the dash installation. It will have a cover about 3/4 x 2 inches. (black plastic) If I remember correctly some of the bounders (older ones) had flip up dashs. Those had the OBDll inthe original factory location. If you find it and it is in a hard to reach place, It has a screw in the side that is easy to remove and you can move the port to a better position. ( I moved mine)
__________________
  Reply With Quote
   
Old 05-16-2011, 04:36 PM   #6
goldwingerx2 is offline
Senior Member
goldwingerx2's Avatar
Winnebago Owners Club
Join Date: Aug 2009
Posts: 209
ga traveler has good info.
__________________
Dean & Mary (Retired U.S.A.F.) plus Purr & Sparkles
12 Itasca Sunova 33C, 12 Smart w/Blue Ox setup, or tow dolly & 12 Prius
  Reply With Quote
   
Old 05-16-2011, 06:23 PM   #7
yardpass is offline
Junior Member
yardpass's Avatar
Join Date: Feb 2011
Posts: 14
Quote:
Originally Posted by ga traveler
Your chassis is a F53. The OBDll plug comes mounted on the steering column support on the right side of the steering wheel. It comes from the factory at this point. However, the factory leaves a two foot lead (wire) so the MH manuf. can move it if it is covered by the dash installation. It will have a cover about 3/4 x 2 inches. (black plastic) If I remember correctly some of the bounders (older ones) had flip up dashs. Those had the OBDll inthe original factory location. If you find it and it is in a hard to reach place, It has a screw in the side that is easy to remove and you can move the port to a better position. ( I moved mine)
Thanks I will look in the morning right now I am at that 4 letter word place (work).

__________________
  Reply With Quote
   
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
1999 Adventurer F53 chassis OBD port ewgivens Winnebago Industries Owner's Forum 3 03-19-2011 12:22 PM
OBD DATA PORT 1999 Ford F-53 chassis ewgivens Winnebago Industries Owner's Forum 4 03-18-2011 07:19 AM
Location of OBD 2 port Marian. Fleetwood Products Owner's Forum 7 03-04-2011 06:51 AM
Position of OBD II port saharakid Monaco Owner's Forum 1 01-17-2011 10:42 AM
obd 2 port convicted09 MH-General Discussions & Problems 4 08-19-2010 01:08 PM

Download our Mobile App






1% for the Planet
» Upcoming Rallies
No events scheduled in
the next 365 days.
» iRV2 on facebook

Our Communities

Our communities encompass many different hobbies and interests, but each one is built on friendly, intelligent membership.

» More about our Communities

Automotive Communities

Our Automotive communities encompass many different makes and models. From U.S. domestics to European Saloons.

» More about our Automotive Communities

RV & Travel Trailer Communities

Our RV & Travel Trailer sites encompasses virtually all types of Recreational Vehicles, from brand-specific to general RV communities.

» More about our RV Communities

Marine Communities

Our Marine websites focus on Cruising and Sailing Vessels, including forums and the largest cruising Wiki project on the web today.

» More about our Marine Communities


Copyright 2002-2012 Social Knowledge, LLC All Rights Reserved.
All times are GMT -6. The time now is 09:56 PM.