RV Trip Planning Discussions

Go Back   iRV2 Forums > THE CHASSIS CLUB FORUMS > Workhorse and Chevrolet Chassis Motorhome Forum
Click Here to Login
Join iRV2 Today

Mission Statement: Supporting thoughtful exchange of knowledge, values and experience among RV enthusiasts.
Reply
  This discussion is proudly sponsored by:
Please support our sponsors and let them know you heard about their products on iRV2
 
Thread Tools Search this Thread Display Modes
 
Old 08-18-2008, 05:01 PM   #1
Senior Member
 
Gary N.'s Avatar
 
Winnebago Owners Club
Workhorse Chassis Owner
Join Date: Mar 2006
Location: Woodslee, ON, Canada
Posts: 128
I'm trying to figure out what wire on the brake light switch to use for the trailer brake controller. When the brake in applied two wires become hot. I think one must operate the electric hydraulic pump and the other the brake lights. Maybe it doesn't matter which one I use to operate the trailer brake controller. I can't seem to find a wiring diagram anywhere so thought I would check in here to see what you guys have to say.
Thanks in advance for you help.
__________________

__________________
Gary & Mary - Woodslee, Ontario
2005 Winnebago 38J, Banks exhaust, Ultra Power
towing '06 Royal Star Venture and '06 Smart diesel
Gary N. is offline   Reply With Quote
Join the #1 RV Forum Today - It's Totally Free!

iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!

You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!

Old 08-18-2008, 05:01 PM   #2
Senior Member
 
Gary N.'s Avatar
 
Winnebago Owners Club
Workhorse Chassis Owner
Join Date: Mar 2006
Location: Woodslee, ON, Canada
Posts: 128
I'm trying to figure out what wire on the brake light switch to use for the trailer brake controller. When the brake in applied two wires become hot. I think one must operate the electric hydraulic pump and the other the brake lights. Maybe it doesn't matter which one I use to operate the trailer brake controller. I can't seem to find a wiring diagram anywhere so thought I would check in here to see what you guys have to say.
Thanks in advance for you help.
__________________

__________________
Gary & Mary - Woodslee, Ontario
2005 Winnebago 38J, Banks exhaust, Ultra Power
towing '06 Royal Star Venture and '06 Smart diesel
Gary N. is offline   Reply With Quote
Old 08-18-2008, 05:06 PM   #3
Senior Member
 
Workhorse Chassis Owner
Join Date: Jan 2007
Posts: 315
Someone else may have better info but as far as know you are correct. It shouldn't matter. However, make sure these aren't hot when your turn signal or hazard lights are on.
__________________
Scott
2003 Allegro, 32BA, W20,'06 Saturn Vue, Demco Aluminator, RM9700, R1150RT B'mer
SE Louisiana
RottenRalph is offline   Reply With Quote
Old 08-18-2008, 05:53 PM   #4
Senior Member
 
Oemtech's Avatar
 
Join Date: Feb 2003
Location: Jarrell, TX 76537
Posts: 4,380
Send a message via AIM to Oemtech
Newmar has 3 wires (pins 2, 4, & 7) run to the 7 pin connector at the rear of the coach available to the user. They are wrapped under the dash. Maybe Winnebago does the same.
__________________
Dale
AKA - Oemy
Oemtech is offline   Reply With Quote
Reply



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Electric Brake Controller Connector - Where is it? W.J. Demo Winnebago Industries Owner's Forum 3 11-16-2008 03:59 PM
"Electric brake" trailer wiring for an Adventurer 35A on a W24 ARNE-T Winnebago Industries Owner's Forum 2 04-07-2008 11:20 AM
Brake Controller Wiring? Old Scout Alpine Coach Owner's Forum 2 11-08-2005 07:08 PM

» Featured Campgrounds

Reviews provided by


Copyright 2002- Social Knowledge, LLC All Rights Reserved.

All times are GMT -6. The time now is 03:50 PM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
×