Go Back   iRV2 Forums > MOTORHOME FORUMS > Class A Motorhome Discussions
Click Here to Login
Join iRV2 Today

Mission Statement: Supporting thoughtful exchange of knowledge, values and experience among RV enthusiasts.
Reply
  This discussion is proudly sponsored by:
Please support our sponsors and let them know you heard about their products on iRV2
 
Thread Tools Search this Thread Display Modes
 
Old 03-16-2014, 04:14 PM   #1
Member
 
Join Date: Apr 2012
Posts: 87
Malfunctioning Slide

Every now and then one of two slides fails to move. I can usually disconnect the 6-lead cable from the circuit board in the electrical bay then reconnect wiggle and the slide will respond to the toggle switch in the MH. there are two of these circuit boards in the bay, one for each slide ...Question : Is it safe to switch the cabling between the two circuit boards?? Inother words , I want use the other circuit board and its connector to move the slide..
__________________

__________________
2003 Fleetwood Discovery 38U
durhamj is offline   Reply With Quote
Join the #1 RV Forum Today - It's Totally Free!

iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!

You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!

Old 03-16-2014, 05:46 PM   #2
Community Moderator
 
"007"'s Avatar


 
Nor'easters Club
Workhorse Chassis Owner
iRV2 No Limits Club
Join Date: Oct 2004
Posts: 26,748
If your unplugging the 6 lead connector than wiggle the connector you may only have loose wire in connector.
Spray some contact cleaning fluid in connector and pins of control board and see if that helps. Also look for loose battery connector and clean that also.
If both control boards are the same you can swap them and see if slide moves correctly.
If it turns out to be faulty board than double click on these pictures for your type control board for ordering.
__________________

__________________
98KSCA, 99MACA, 03 KSCA-3740- 8.1 Chev-- ALLISON Trans, now in good hands
VISIT the NEWMAR QUICK TIPS & EASYMODS 1 & 2
QUICK TIPS # 3
RV SYSTEMS & APPLIANCES & RECALLS --- TECH INFORMATION
"007" is offline   Reply With Quote
Old 03-16-2014, 08:28 PM   #3
Senior Member
 
waroland's Avatar
 
Join Date: May 2009
Location: Mt Juliet, TN (Homebase)
Posts: 432
I had the solder on one pin on the plug on the board bad. You may want to remove your board and check the plug for bad solder joints.
__________________
2002 Fleetwood Revolution 38B
2006 Honda CR-V Air Force One
waroland is offline   Reply With Quote
Old 03-30-2014, 09:10 PM   #4
Member
 
Join Date: Apr 2012
Posts: 87
Thanks for the replies. Turns-out both boards had cold solder joints.. The rear board's 6 lead connector had six cold solder joints. Looked like it was done by a 2nd grader. The front board had 2 cold joints... Resoldered, now works fine.
__________________
2003 Fleetwood Discovery 38U
durhamj is offline   Reply With Quote
Reply

Tags
slide



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Driver's seat moves into slide when moving slide TXduo Monaco Owner's Forum 6 03-12-2014 05:37 PM
Slide out of Alignment Glen and Sal National RV Owner's Forum 10 03-03-2014 07:55 PM
Slide problems with Slide Show emcee MH-General Discussions & Problems 6 02-05-2014 06:35 PM
Living Room Slide adjustment D in Davie Newmar Owner's Forum 1 09-12-2013 09:39 PM
Hydraulic slide questions janieD Excel Owner's Forum 10 06-24-2013 04:25 PM

» Virginia Campgrounds

Reviews provided by


Copyright 2002- Social Knowledge, LLC All Rights Reserved.

All times are GMT -6. The time now is 07:32 AM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2017, vBulletin Solutions, Inc.