 |
11-03-2019, 01:05 PM
|
#1
|
|
Junior Member
Join Date: Nov 2019
Posts: 11
|
Slide Issue
Good day, I have a 2000 Newmar Dutch Star, it has 2 slides, I started putting the slide out b4 I realized it was still locked! It stopped functioning, I got the slide unlocked and it went out a couple of inches. Now the switch does nothing on either slide. Thanks in advance
|
|
|
 |
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
|
11-03-2019, 01:23 PM
|
#2
|
|
Community Administrator
Tiffin Owners Club
Join Date: Sep 2013
Location: DFW, Texas
Posts: 21,526
|
Quote:
Originally Posted by Ronbon
Good day, I have a 2000 Newmar Dutch Star, it has 2 slides, I started putting the slide out b4 I realized it was still locked! It stopped functioning, I got the slide unlocked and it went out a couple of inches. Now the switch does nothing on either slide. Thanks in advance
|
Check your fuses or breakers. If you overloaded the motor when trying to extend, you probably blew a fuse.
__________________
 2017 Phaeton 40IH XSH Maroon Coral - Power Glide Chassis with IFS
Previous '15 Tiffin Allegro RED 38QRA and '06 Itasca Sunrise 35A
'16 Jeep JKU Wrangler Sahara or '08 Honda Goldwing
|
|
|
|
|
11-03-2019, 01:57 PM
|
#3
|
|
Moderator Emeritus
Nor'easters Club Workhorse Chassis Owner iRV2 No Limits Club
Join Date: Oct 2004
Posts: 30,785
|
Welcome to irv2, Ron
This link will give you
slide information and you may have blown a fuse for your slides.
If slide in now crooked in its opening you will need to release the torque bushings and with help push slide in than re tighten the bushings.
Brochure --- Owners Guide --- Fuse wiring info.
Enjoy the forums and join us in the Newmar Forum
|
|
|
|
|
11-03-2019, 05:29 PM
|
#4
|
|
Junior Member
Join Date: Nov 2019
Posts: 11
|
Slides
Good day, I have a 2000 Newmar Dutch Star, it has 2 slides, I started putting the slide out b4 I realized it was still locked! It stopped functioning, I got the slide unlocked and it went out a couple of inches. Now the switch does nothing on either slide. Thanks in advance
|
|
|
|
|
11-04-2019, 03:59 AM
|
#5
|
|
Senior Member
Join Date: Jan 2015
Location: Prescott, Arizona
Posts: 3,564
|
First, Welcome to the group. Extra knowledge is always handy.
If both locks were in place and the slide didn't move the problem could be the motor or the Transtorque Bushing which in my case is located near the motor. Open the storage bays below the slide to check. If you need a part I've found Newmar to be very helpful even if you did not purchase the rig new.
If the slide is out of alignment the Transtorque Bushing needs to be released which allows the drive rods to be adjusted independently. The Transtorque Bushing will then need to be tightened.
Been there Done that. Good Luck!!
__________________
'04 Newmar MADP, 1100w of solar, Rubicon toad
|
|
|
|
|
11-04-2019, 10:26 AM
|
#6
|
|
Senior Member/RVM #90
Monaco Owners Club
Join Date: Nov 2002
Location: Columbus, MS
Posts: 54,771
|
Hi ! Welcome to IRV2! We're sure glad you joined the gang! 
Good luck, happy trails, and God bless!  
__________________
Joe & Annette
Sometimes I sits and thinks, sometimes I just sits.....
2002 Monaco Windsor 40PBT, 2013 Honda CRV AWD
|
|
|
|
|
11-04-2019, 10:20 PM
|
#7
|
|
Moderator Emeritus
Nor'easters Club Workhorse Chassis Owner iRV2 No Limits Club
Join Date: Oct 2004
Posts: 30,785
|
You changed your name from yesterday when I answered your same question.
Here is information you need.
You need to go to the second or third page your question will move fast on this busy forum not so much on other forums.
|
|
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Linear Mode
