|
|
06-13-2019, 09:21 AM
|
#15
|
Senior Member
Join Date: Apr 2010
Location: Georgia
Posts: 576
|
Our 4008 original pump failed on our last outing. Ordered and received the new 4048 last week. After the install this am, pump runs and pumps great. But pump will not shut off! Tried adjusting the shut off switch to no avail. Only turned the adjustment screw 1/2 round out to lower the shutoff pressure. Also increased the bypass pressure by 1/2 turn in. According to instructions the full bypass pressure should be 10 psi higher than shutoff pressure or pump will continue to run. Scratching my head on this. Anyone have the same issue with a new pump install?
And as always, things always go south when under pressure. Plans were to leave tomorrow am for a week on the road.
Thanks, GrAndy
|
|
|
|
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
06-13-2019, 10:27 AM
|
#16
|
Senior Member
Entegra Owners Club
Join Date: Jun 2004
Location: Bayfield, Ontario
Posts: 5,470
|
Quote:
Originally Posted by SAS30
Our 4008 original pump failed on our last outing. Ordered and received the new 4048 last week. After the install this am, pump runs and pumps great. But pump will not shut off! Tried adjusting the shut off switch to no avail. Only turned the adjustment screw 1/2 round out to lower the shutoff pressure. Also increased the bypass pressure by 1/2 turn in. According to instructions the full bypass pressure should be 10 psi higher than shutoff pressure or pump will continue to run. Scratching my head on this. Anyone have the same issue with a new pump install?
And as always, things always go south when under pressure. Plans were to leave tomorrow am for a week on the road.
Thanks, GrAndy
|
Right out of the box the cut in and cut out pressures should be fairly close. Any chance a valve in the wet bay is in the wrong position?
__________________
Don & Gerri
2014 Entegra Anthem 44B
2014 Honda CRV Touring
1300W Solar, 1200AH LiFePO4 FMCA F443497
|
|
|
06-13-2019, 06:24 PM
|
#17
|
Registered User
Join Date: Jan 2018
Posts: 1,385
|
Quote:
Originally Posted by Tom78418
I spoke with Entegra CS before ordering the 4048 pump. Even with being told there was sufficient amp capacity for the pump my reservations were resolved knowing there is a higher amp source being the macerator wiring. A simple relay from auto parts store could be used to take advantage of the higher amp source.
As it turned out the 4048 pump has worked flawlessly with the existing wiring. We travel extensively in our coach and encounter a broad range in water quality. All water used in the coach is drawn from the fresh water tank automatically kept filled through heavily filtered city water. As a result the pump is constantly used.
|
When I did my 4048 upgrade, it blew the breaker almost immediately, and constantly.
The breaker is 5 amps, and the seelevel switch just 7 amps.
I used an autoparts store relay powered by the macerator power.
|
|
|
06-14-2019, 07:46 AM
|
#18
|
Senior Member
Winnebago Owners Club
Join Date: Mar 2014
Posts: 14,891
|
We have upgraded to the 4048. So far we are on our third. Two replaced under warranty. SHURflo has been very good about replacing the pumps.
__________________
Gordon and Janet
Tour 42QD/InTech Stacker
|
|
|
06-16-2019, 07:05 PM
|
#19
|
Senior Member
Join Date: Apr 2010
Location: Georgia
Posts: 576
|
Quote:
Originally Posted by SAS30
Our 4008 original pump failed on our last outing. Ordered and received the new 4048 last week. After the install this am, pump runs and pumps great. But pump will not shut off! Tried adjusting the shut off switch to no avail. Only turned the adjustment screw 1/2 round out to lower the shutoff pressure. Also increased the bypass pressure by 1/2 turn in. According to instructions the full bypass pressure should be 10 psi higher than shutoff pressure or pump will continue to run. Scratching my head on this. Anyone have the same issue with a new pump install?
And as always, things always go south when under pressure. Plans were to leave tomorrow am for a week on the road.
Thanks, GrAndy
|
Man do I feel dumb! After checking this out for another hour or so, realized that the kitchen sink faucet was partially open. Did not realize this, as when the pump would not shut off, I would unplug it and walk around and through the coach to check that all faucets were closed. The wife later came out while I had the pump running and asked was the kitchen faucet supposed to be open?
Sometimes it just the obvious that I overlook.
|
|
|
06-17-2019, 10:42 AM
|
#20
|
Senior Member
Join Date: Oct 2012
Location: Louisiana
Posts: 11,537
|
Don't beat yourself up too much......! We'd all be black and blue a few days each month/year....
Gary
__________________
Gary and Dee, Zowie and Bowie (traveling cat sibs)
2019 Cornerstone 45B, X15-605hp, Imperial, Spartan K3,
2013 Honda CR-V toad, Demco Excali-Bar II,
Demco Baseplate, Demco Toad Light system, 73 de W5FI
|
|
|
06-24-2019, 05:22 PM
|
#21
|
Senior Member
Join Date: Aug 2016
Location: Scottsdale, AZ
Posts: 3,122
|
Quote:
Originally Posted by Tom78418
I did the 4048 upgrade and yes it is much better and unfortunately louder. One problem is it is mounted on a drum (wall). I saw a post where someone made a plastic base and mounted the pump on top of the macerator with flexible hose connecting to the original plumbing. Definitely would help with the noise. Then again I take comfort knowing any leak will have an audible announcement. I did not shut off the outside nozzle fully leaving a trickle. The pump let me know. I just installed the tech service bulletin parts for the ice maker and the pump lets us know when it is filling the tray.
There is a down side to the 4048 pump. The flow rate is about 25% greater than the 4008 and eats up the fresh water tank faster. Have to be more careful when off grid.
|
Tom, I would be the guilty party who did that.
I know all of you who've installed Shurflo 4048 pumps don't want to hear it, but the Aquajet pump is noticeably quieter. More info here:
http://www.irv2.com/forums/f278/new-...by-433673.html
__________________
Larry & Amy Beckner
Scottsdale, AZ
2022 Newmar Super Star 4061
|
|
|
06-25-2019, 11:00 AM
|
#22
|
Senior Member
Entegra Owners Club Spartan Chassis
Join Date: Aug 2015
Posts: 467
|
That was a really nice install. Problem with forums is trying to find something. One question. When you mounted the plastic plate did you use the existing SaniCon threaded holes or make your own. Again, awesome mod.
|
|
|
06-25-2019, 02:06 PM
|
#23
|
Senior Member
Join Date: Aug 2016
Location: Scottsdale, AZ
Posts: 3,122
|
Quote:
Originally Posted by Tom78418
That was a really nice install. Problem with forums is trying to find something. One question. When you mounted the plastic plate did you use the existing SaniCon threaded holes or make your own. Again, awesome mod.
|
Tom, click on the link below. It will take you to a bit of a long post, but I believe it will answer your question:
http://www.irv2.com/forums/f278/new-...ml#post4676875
__________________
Larry & Amy Beckner
Scottsdale, AZ
2022 Newmar Super Star 4061
|
|
|
06-25-2019, 06:59 PM
|
#24
|
Senior Member
Entegra Owners Club Spartan Chassis
Join Date: Aug 2015
Posts: 467
|
Looks like I have a winter lay-up project with some excellent well throughout plans. Excellent write-up.
Thanks for the info,
Tom
__________________
Tom and Jodie
2017 Entegra Cornerstone 44B
2013 Jeep Wrangler Unlimited
|
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|