|
06-13-2015, 09:46 PM
|
#1
|
Senior Member
Join Date: Mar 2014
Location: Fremont, CA
Posts: 170
|
Installed brisk air 2, not working
Hello all, well I'm changing out the old penguins on my rv. I went with the 15000 btu. Cool only.
Ok, so here's what's going on. I turn on the generator and main breaker. And also breaker for front AC. Doesn't come on.. I checked one of the plugs in the kitchen, so there's power. I don't have the cover installed , does that have to be on before unit works?
Does the inverter and transfer switch have to be on?. I had everything off because working with electric.
Thanks, Chris
|
|
|
|
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
06-14-2015, 04:21 AM
|
#2
|
Moderator Emeritus
Country Coach Owners Club Appalachian Campers Gulf Streamers Club
Join Date: Mar 2000
Location: Chattanooga, Tn.
Posts: 12,060
|
You will need 12 vdc for control function and 120vac for fan motor and compressor operation. Make certain the house battery bank is connected and the circuit breakers on the generator is on. Verify you have both at the control board. If it does not come on after several minutes (allowing for time delay) try connecting to shore power. If it works on shore power but not generator, you have a bad transfer switch.
__________________
Mike, RVIA & RVSA Certified Master RV Technician
Amy, Dr. Assistant - Roxie & Mei Ling, four legs each
2000 Gulf Stream Scenic Cruiser 450 hp & 1330# torque
06 Saturn Vue, 06 Chevy Z71 4x4 & 2014 Corvette Z51 M7
|
|
|
06-14-2015, 07:56 AM
|
#3
|
Senior Member
Join Date: Mar 2014
Location: Fremont, CA
Posts: 170
|
Rv wizard, thanks for your reply. I have installed 1 of the 4 battery's and it's fully charged. I checked for power at wall socket and get power, but it shows 108volts with plug in tester. My other wall plugs are off. And it's normal, because the inverter needs to be on.
Do I check for power at the breaker? How would I check AC voltage at the air conditioner? Do I leave attached and check at the wire nuts?
Does this unit have a control board? It's a B59516, non ducted and has ceiling controls.
Thank You, Chris
|
|
|
06-14-2015, 11:28 AM
|
#4
|
Senior Member
Join Date: Dec 2000
Location: Weatherford, Tx 76086 USA
Posts: 1,715
|
that unit should have come on when you connected it to 120 power. It is a manual unit with no external thermostat
__________________
Ernie Ekberg
Foretravel
Mineral Wells, Texas
|
|
|
06-14-2015, 12:23 PM
|
#5
|
Senior Member
Join Date: Mar 2014
Location: Fremont, CA
Posts: 170
|
Thanks for your reply ernie. I have no AC current. Either Shore power or generator. I checked for power at the breaker and nothing. . It worked fine before. This is driving me crazy. Chris
|
|
|
06-14-2015, 12:44 PM
|
#6
|
Senior Member
Join Date: Dec 2000
Location: Weatherford, Tx 76086 USA
Posts: 1,715
|
turn all your breakers on, inverter, etc. if you have wire nuts on your new a/c unit, everything should work. are you plugged into shore power?
__________________
Ernie Ekberg
Foretravel
Mineral Wells, Texas
|
|
|
06-14-2015, 04:00 PM
|
#7
|
Senior Member
Join Date: Mar 2014
Location: Fremont, CA
Posts: 170
|
Ernie, I got it working. The breaker on the generator was tripped and one of the 110 breakers was bad. Got it going. Thanks for your help. Chris
|
|
|
06-14-2015, 04:15 PM
|
#8
|
Senior Member
Join Date: Dec 2000
Location: Weatherford, Tx 76086 USA
Posts: 1,715
|
Brisk Airs are great. A little noisy but I don't like to sweat
__________________
Ernie Ekberg
Foretravel
Mineral Wells, Texas
|
|
|
06-14-2015, 04:19 PM
|
#9
|
Senior Member
Solo Rvers Club
Join Date: Mar 2012
Location: Cape Girardeau ,Mo
Posts: 165
|
Great to here you like the Brisk air as I am getting ready to install one as a second unit in my bedroom this week .
|
|
|
06-14-2015, 04:42 PM
|
#10
|
Senior Member
Join Date: Dec 2000
Location: Weatherford, Tx 76086 USA
Posts: 1,715
|
I added one to my previous coach 3 years ago. All mechanical, no wall thermostat to mess with. Easy install. Make sure all old debris cleaned off the roof so new gasket will be effective
__________________
Ernie Ekberg
Foretravel
Mineral Wells, Texas
|
|
|
06-14-2015, 04:54 PM
|
#11
|
Senior Member
Join Date: Mar 2014
Location: Fremont, CA
Posts: 170
|
The best thing I did was to rent a material lift.. 50 bux for the day, no fighting with a ladder or strained back. My old ac's gasket was really on there. Plus the PO put silicone over an external gasket. .. still leaked . SMH
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|