Go Back   iRV2 Forums > MOTORHOME FORUMS > MH-General Discussions & Problems
Click Here to Login
Join iRV2 Today

Mission Statement: Supporting thoughtful exchange of knowledge, values and experience among RV enthusiasts.
Reply
  This discussion is proudly sponsored by:
Please support our sponsors and let them know you heard about their products on iRV2
 
Thread Tools Search this Thread Display Modes
 
Old 10-11-2010, 10:20 PM   #1
Junior Member
 
Join Date: Feb 2009
Posts: 18
holding tank sensors

i have a 2005 national rv seabreeze , model 1321, ford chassis . can any one tell me where the holding tank sensors are located. i don't want to tear any thing apart that i don't have to. i need to get to my tank sensors to make sure they have a good ground. both the black and gray tanks are reading empty when i know they are not. the jrv company tested the circuit board and said its ok. thanks for any help. jimburr.
__________________

__________________
jimburr1 is offline   Reply With Quote
Join the #1 RV Forum Today - It's Totally Free!

iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!

You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!

Old 10-12-2010, 03:50 PM   #2
Senior Member
 
puttin's Avatar
 
Winnebago Owners Club
Ford Super Duty Owner
Join Date: Dec 2009
Posts: 1,284
Before you do any tearing apart- is the propane also showing empty, and any other tank measurements at your panel? Check the ground for all these if that's the case. You'll know what to look for if you get under your rig and find the sensor circuit. You'll see some screws with wires attached to each one- those are the probes, and they are probably ok...somewhere further upstream in that wire loom is where you should find a wire going to ground...either on the chassis or maybe up to the panel inside- I'm guessing that wire is loose, broken or otherwise disconnected.
__________________
puttin is offline   Reply With Quote
Reply



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
How do you access gray tank sensors on Sunova? DavidLyle Winnebago Industries Owner's Forum 5 06-01-2010 03:18 PM
Cleaning the holding tank sensors Beetlebailey 5th Wheel Discussion 12 10-03-2007 06:34 PM
Black Holding Tank Sensors fep Alpine Coach Owner's Forum 8 04-04-2007 09:19 PM
Grey Water Holding Tank AXE RV Systems & Appliances 5 03-10-2007 07:39 PM
Removing holding tank sensors?? smlranger Winnebago Industries Owner's Forum 6 07-02-2005 06:07 AM

» Virginia Campgrounds

Reviews provided by


Copyright 2002- Social Knowledge, LLC All Rights Reserved.

All times are GMT -6. The time now is 07:52 PM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2017, vBulletin Solutions, Inc.