Journey with Confidence RV GPS App RV Trip Planner RV LIFE Campground Reviews RV Maintenance Take a Speed Test Free 7 Day Trial ×
RV Trip Planning Discussions

Go Back   iRV2 Forums > MOTORHOME FORUMS > MH-General Discussions & Problems
Click Here to Login
Register FilesVendors Registry Blogs FAQ Community Calendar Today's Posts Search Log in
Join iRV2 Today

Mission Statement: Supporting thoughtful exchange of knowledge, values and experience among RV enthusiasts.
Reply
  This discussion is proudly sponsored by:
Please support our sponsors and let them know you heard about their products on iRV2
 
Thread Tools Search this Thread Display Modes
 
Old 10-07-2010, 12:44 PM   #1
Senior Member
 
Join Date: Feb 2010
Posts: 4,654
Ridge cover bonding?

This may not be the correct term, I am asking about the material that is crossectional shape of U about an inch wide and 1/2 inch tall that is used to cover the seams between the roof and sidewalls on fiberglass sidded coaches.

Ours has lifted in a few places and there does not sem to be any glue, screws or other materials to secure it.

I am guessing there could have been some sort of epoxy a long time ago which has since fell off before we got our coach.


We need to re-attach in a few places, was thinking about SS drywall type screws along with some sort of adhesive then cover with caulking.

Before we start the project we would like to know what else has been tried so we do not re-invent the wheel and have it square...
TQ60 is offline   Reply With Quote
Join the #1 RV Forum Today - It's Totally Free!

iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!

You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!

Old 10-08-2010, 02:37 AM   #2
Moderator Emeritus
 
RV Wizard's Avatar


 
Country Coach Owners Club
Appalachian Campers
Gulf Streamers Club
Join Date: Mar 2000
Location: Chattanooga, Tn.
Posts: 12,060
This molding is secured at the factory with screws. If water has gotten in, you might have wood rot that will have to be dealt with to have a backer for new or replaced screws to bite into. On the top a self leveling lap sealant like Dicor should be used to cover the edge of the molding and heads of screws. Check into the possibility of rot and let us know what you find and then we can help you more.
__________________
Mike, RVIA & RVSA Certified Master RV Technician
Amy, Dr. Assistant - Roxie & Mei Ling, four legs each
2000 Gulf Stream Scenic Cruiser 450 hp & 1330# torque
06 Saturn Vue, 06 Chevy Z71 4x4 & 2014 Corvette Z51 M7
RV Wizard is offline   Reply With Quote
Old 10-08-2010, 10:52 AM   #3
Senior Member
 
Join Date: Feb 2010
Posts: 4,654
No screws found.

We have looked and there are no screws in this strip except for a couple that a previous owner installed.

The shape is inverted "U", there are no flanges for screws, the only place for screws is on the top.

The material looks to be a rubber like stuff, same as what is on the top of the coach.

So far there is minimal water exposure, so a little sanding will clean that up, just need to figure out how it was done from the factory so we can at least attempt to correct it in the same manner.
TQ60 is offline   Reply With Quote
Old 10-08-2010, 12:37 PM   #4
Senior Member
 
Me n Slowpoke's Avatar
 
Texas Boomers Club
Gulf Streamers Club
Ford Super Duty Owner
Coastal Campers
Join Date: Jul 2010
Location: Texas
Posts: 173
The shape is inverted "U", there are no flanges for screws, the only place for screws is on the top

Could this be attached/part of the bottom of the strip (with the screws) that seals the roof to the side walls, which could be for the awning material? Just a thought as mine has one and the awning came off when the previous owner had it , it is damaged where the wind blew it up and over the MH . but it is also a u shape with the opening pointing out.
__________________
Me & Slowpoke, USMC [1993 Gulfstream Sunvoyager M8345, F53 Chassis ]

"Travlin with a song and prayer"
Me n Slowpoke is offline   Reply With Quote
Reply



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Needing to buy a cover PlayItForwrd MH-General Discussions & Problems 6 09-30-2010 10:11 AM
Journey Step Cover b52bomber Winnebago Industries Owner's Forum 4 06-19-2010 08:09 AM
Dragged filter cover up the Leelanau peninsula Brigadoon Newmar Owner's Forum 15 04-25-2009 07:41 AM
A/C cover (shroud) blown off Judy Fleming Alpine Coach Owner's Forum 4 03-24-2009 10:09 PM
Select Comfort bed cover tearing apart inside AFChap Winnebago Industries Owner's Forum 7 08-01-2008 04:43 AM

» Featured Campgrounds

Reviews provided by


All times are GMT -6. The time now is 11:02 PM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.