Community Forums

DRL1950 · 09-29-2019, 08:12 AM

When running zones 1 and 3 on Furnace I am getting heat from zone 3 in the rear bath, but only getting cold air blowing up front. So I am assuming that warm water is not circulating somewhere but not sure what to check or where to look. Any help appreciated

wishalls · 09-29-2019, 08:53 AM

Check your distribution panel by oasis furnace for any red lights. Sounds like the 1 loop pump is not working. If it has been a long time since it has run it may be a stuck check valve.

DRL1950 · 09-29-2019, 09:08 AM

Quote:

Originally Posted by wishalls

Check your distribution panel by oasis furnace for any red lights. Sounds like the 1 loop pump is not working. If it has been a long time since it has run it may be a stuck check valve.

Good suggestion, went out to check all lights are green. Other strange this is that I turned on all three of the floor heat zones and they all seem to be working, so now really puzzled as to why no warm air out of the vent.

wishalls · 09-29-2019, 10:59 AM

Others may know better about 2015 but I believe your floor heat is electrical and not associated with the oasis system.

what next · 09-29-2019, 02:30 PM

Call ITR they answer phone and are very helpful. First thing is feel pumps see if they are running. Check check valves see if hot is getting past them. Sometimes the check valve sticks, I have had to give them a tap. ITR will send you info and photo.

DRL1950 · 09-29-2019, 03:10 PM

Ok I am going to sound stupid but who is ITR and where are the pumps and check valves located Thanks for responding

DRL1950 · 09-29-2019, 03:12 PM

Quote:

Originally Posted by wishalls

Others may know better about 2015 but I believe your floor heat is electrical and not associated with the oasis system.

You could be right wasn’t sure if they were related
Thanks for taking the time to respond

wishalls · 09-29-2019, 03:49 PM

Quote:

Originally Posted by DRL1950

Ok I am going to sound stupid but who is ITR and where are the pumps and check valves located Thanks for responding

ITR is the company that makes your Oasis furnace. The pumps and check valves are in the distribution module. The module is behind your electric cord, but you get access from the passenger side of coach. Open the door just in front of the pegboard area,look across the coach and you will see a panel that can be removed. You can see the green distribution module behind the panel. It is a pain to get to. Remove front of the distribution panel and you will see the pumps and check valves. The zone 1 loop pump is the center pump. Good luck

ftharrisiii · 09-29-2019, 05:13 PM

Here is a photo of the Oasis distribution panel with the slide tray and the front access panel removed.

Click image for larger version

Name: 20181029_163055.jpg
Views: 41
Size: 308.8 KB
ID: 261844

DRL1950 · 09-30-2019, 02:05 PM

Wow! Thanks everyone, that could only have been better if y’all just came out here and fixed it for me! Can always count on this forum for an answer about pretty much anything. I will be all over it this weekend, thanks again, I will post how I make out.

DRL1950 · 10-04-2019, 01:48 PM

Thanks again to everyone who posted, finally got in there today and removed the panels. Zone one was not pumping so gave it a little whack, and off it went. I figure I may have a loose connection but now that I know where everything is I should be able to sort it out.

"007" · 10-04-2019, 02:29 PM

If you check the stickies top of forum you will find what you need.

srrobe · 10-04-2019, 08:17 PM

You have a circulation pump that is failing. You may get away with smacking it for a while but eventually you will have to replace the pump. They can be purchased from ITR. Ive had two go bad.