Just noticed front or Living Room AC not coming on. When I went to the silverleaf screen for Living Room above the Fan Icon it shows shed.
When I go to the load shedding screen Engine block heater shows Off and AC 1 which is Living Room AC compressor shows ok but Fan shows off.
I will attach a photo of Silverleaf screen when Living Room is high lighted. Note the Fan will run in forced manual but still shows off on load shedding screen.
Anyone had this problem?
__________________
David and Sharon
2017 Newmar London Aire 4519
2020 Jeep Wrangler Rubicon
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
I had this same problem with my bedroom unit. Others have attributed the problem with the TM250. I tend to believe that. I had other issues with the TM250 (dual phase capacity options incorrect). I recently had my TM250 reflashed by Silverleaf.
I would try to disconnecting the TM250 and see if the problem goes away. Keep in mind that other TM250 functions will not work, namely bath and outdoor temperature readings. While disconnected, I also had issue with Oasis AC units turning off after a few hours.
Thanks all, got Silverleaf on phone and he walked me through troubleshooting.
He had me unplug main inlet to TM250 front air came on immediately.
They are sending me a new TM250 as when I gave him the version number it was not updatable.
So it is unplugged and once I get home, I will install the new TM250.
Thanks to All for the help!
__________________
David and Sharon
2017 Newmar London Aire 4519
2020 Jeep Wrangler Rubicon
Keep an eye on the Oasis AC1/AC2. When I pulled my TM250 to sent it back to the Silverleaf for reprogramming I found that the AC1/AC2 would turn off after several hours. I never figured out the cause, but the problem did clear itself after the TM250 was plugged back in. Its really only a problem when you wake up in the morning and find that you don't have any hot water. I'd be curious to know if you see this issue.
Keep an eye on the Oasis AC1/AC2. When I pulled my TM250 to sent it back to the Silverleaf for reprogramming I found that the AC1/AC2 would turn off after several hours. I never figured out the cause, but the problem did clear itself after the TM250 was plugged back in. Its really only a problem when you wake up in the morning and find that you don't have any hot water. I'd be curious to know if you see this issue.
I did notice when I unplugged the TM-250, I had an error under System diagnostics stating “Oasis no outside temperature differential” as we were load shedding or so I thought at 1st, I only ran burner before taking showers and that seemed to work fine.
__________________
David and Sharon
2017 Newmar London Aire 4519
2020 Jeep Wrangler Rubicon
To confirm it's your TM-250 or the A/C unit itself- set the front unit on a really cold demand temperature like 55 degrees- turn your heat setting off or way down to 40 degrees- turn on Cool & see if the front A/C starts- if it does you have a faulty TM-250 sensor- short term you can use it by setting the temperature down to a relative setting where it is comfortable- that won't be an actual finite reading.
To confirm it's your TM-250 or the A/C unit itself- set the front unit on a really cold demand temperature like 55 degrees- turn your heat setting off or way down to 40 degrees- turn on Cool & see if the front A/C starts- if it does you have a faulty TM-250 sensor- short term you can use it by setting the temperature down to a relative setting where it is comfortable- that won't be an actual finite reading.
Linear Mode
