|
05-14-2013, 02:56 PM
|
#1
|
Senior Member
Join Date: Mar 2009
Location: Apollo Beach & Key West , FL
Posts: 3,837
|
Precision Circuits Monitor Question
We recently picked up our 2013 Dutch Star and I'm trying to get accustomed to the difference between this and our previous coach.
The Precision Circuits Monitor that is installed did not come with any manual/instructions ... I'll talk to the dealer about that.
In the mean time, in looking at the monitor, while on the gen set ( we are in a storage lot without shore power) it shows the load on L1 and L2 and it varies , as expected, when various things are turned on and off. Also on the display, is what I understand to be the shed list... it has the item, (e.g. AC1, WH,etc.) followed by status ( e.g. on) followed by "0 A" which I assume is supposed to indicate the amp draw. What is this display supposed to be showing me ? When an item is on via gen power, it is always "0". Is it the amps put thru via the inverter to the device ?
There are 3 buttons on the panel, the top one and the bottom one function to scroll thru the display... the middle one doesn't seem to do anything... ideas ?
Thanks
|
|
|
|
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
05-14-2013, 04:18 PM
|
#2
|
Moderator Emeritus
Nor'easters Club Workhorse Chassis Owner iRV2 No Limits Club
Join Date: Oct 2004
Posts: 30,785
|
Congrats with your new DSDP PanJH.
Here is a PDF found in the COM_NET2 LINK.
Here is a TSB for washing your coach.
|
|
|
05-14-2013, 08:40 PM
|
#3
|
Senior Member
Newmar Owners Club Freightliner Owners Club
Join Date: Jun 2011
Location: Texas
Posts: 6,426
|
Quote:
Originally Posted by PanJH
We recently picked up our 2013 Dutch Star and I'm trying to get accustomed to the difference between this and our previous coach.
The Precision Circuits Monitor that is installed did not come with any manual/instructions ... I'll talk to the dealer about that.
In the mean time, in looking at the monitor, while on the gen set ( we are in a storage lot without shore power) it shows the load on L1 and L2 and it varies , as expected, when various things are turned on and off. Also on the display, is what I understand to be the shed list... it has the item, (e.g. AC1, WH,etc.) followed by status ( e.g. on) followed by "0 A" which I assume is supposed to indicate the amp draw. What is this display supposed to be showing me ? When an item is on via gen power, it is always "0". Is it the amps put thru via the inverter to the device ?
|
When on 50 Amp or Generator, it does not monitor the devices for amp pull, as it does not shed loads. Only on 30/20/15 does it monitor the actual load, and then shed if necessary.
What is the build date of your coach? You may have the newest firmware installed. If not, then you will only have the option for 30/20 on the selection.
Quote:
There are 3 buttons on the panel, the top one and the bottom one function to scroll thru the display... the middle one doesn't seem to do anything... ideas ?
Thanks
|
This middle button is only used when plugged into less than 50 amp service. This will cycle between 30/20 or 30/20/15 depending on your software version.
__________________
2022 London Aire 4551 * 2022 GD Imagine 2800BH * 2021 RAM 3500 DRW * 2020 Wrangler
NHSO (Newmar Hoot, Sevierville Original)
Kindness Matters
|
|
|
05-15-2013, 06:06 AM
|
#4
|
Senior Member
Join Date: Mar 2009
Location: Apollo Beach & Key West , FL
Posts: 3,837
|
I'll have to look at the release level when I get back down there.... it was built in April so I'm pretty sure it will be the newest.
Thanks for the info and the links... guess it makes sense now !
|
|
|
05-15-2013, 10:03 AM
|
#5
|
Senior Member
Join Date: May 2011
Posts: 195
|
go to precision circuits web site and you can down load a complete pdf manual
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|