|
06-19-2021, 01:04 PM
|
#1
|
Senior Member
Join Date: Mar 2011
Posts: 754
|
Slide drive problem
Hi guys, 2014 Ventana 4037
On the full wall slide, rear motor is turning, torque bushing spinning, but drive shaft not rotating ?
Also see a brass colored stud on right side of motor housing that is spinning when motor engaged.
Could this be something with Torque bushing, or deeper problems ?
Thanks
__________________
2014 Newmar Ventana 4037 / 4018
2015 Jeep Grand Cherokee Ltd.
1940 Chevrolet Pickup
|
|
|
|
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
06-19-2021, 01:13 PM
|
#2
|
Senior Member
Monaco Owners Club
Join Date: Jun 2010
Location: Willard .Missouri
Posts: 192
|
Make sure the bolts are in the drive shaft Next to the motor
|
|
|
06-19-2021, 01:19 PM
|
#3
|
"Formerly Diplomat Don"
Newmar Owners Club
Join Date: Apr 2005
Location: Moorpark, Ca.
Posts: 24,076
|
Sounds like the trans torque bushing is loose. Kind of odd as their very difficult to break loose.
__________________
Don & Mary
2019 Newmar Dutch Star 4018 (Freightliner)
2019 Ford Raptor
|
|
|
06-19-2021, 01:37 PM
|
#4
|
Senior Member
Join Date: Mar 2011
Posts: 754
|
Quote:
Originally Posted by Dutch Star Don
Sounds like the trans torque bushing is loose. Kind of odd as their very difficult to break loose.
|
Kind of my thought too
What is procedure to tighten ? I do have crows foot wrench. Confused as to left or right hand thread postings. To tighten do I want to go clockwise or counterclockwise?
Do I need a pipe wrench on the outside collar or the driveshaft while tightening ?
Thanks
__________________
2014 Newmar Ventana 4037 / 4018
2015 Jeep Grand Cherokee Ltd.
1940 Chevrolet Pickup
|
|
|
06-19-2021, 07:26 PM
|
#5
|
"Formerly Diplomat Don"
Newmar Owners Club
Join Date: Apr 2005
Location: Moorpark, Ca.
Posts: 24,076
|
I'll be honest, I carry the tools, but have never had to adjust one. If yours is really that loose, I would put a wrench on it and see which way it moves more easily, to determine direction. Here are a couple of posts about it.
https://www.irv2.com/forums/f84/slid...al-360766.html
https://www.irv2.com/forums/f103/tra...st-466435.html
__________________
Don & Mary
2019 Newmar Dutch Star 4018 (Freightliner)
2019 Ford Raptor
|
|
|
06-19-2021, 09:14 PM
|
#6
|
Senior Member
Join Date: Mar 2011
Posts: 754
|
Well, I put the wrench on the torque bushing, and it was loose
Thank goodness I had picked up that claw foot wrench a couple of years ago
Tightened the heck out of it ( my torque wrench only goes to 80 ft lbs ), so used a big socket bar
Tried it out - things running smoothly again
Thanks for you help
__________________
2014 Newmar Ventana 4037 / 4018
2015 Jeep Grand Cherokee Ltd.
1940 Chevrolet Pickup
|
|
|
06-20-2021, 02:28 PM
|
#7
|
"Formerly Diplomat Don"
Newmar Owners Club
Join Date: Apr 2005
Location: Moorpark, Ca.
Posts: 24,076
|
Glad you got it fixed. I carry a 1.5" wrench and crows foot. Knock on wood, haven't needed it so far. On my 2019, I only have the transtorque bushing on the bedroom motor.
__________________
Don & Mary
2019 Newmar Dutch Star 4018 (Freightliner)
2019 Ford Raptor
|
|
|
06-22-2021, 10:22 PM
|
#8
|
Moderator Emeritus
Nor'easters Club Workhorse Chassis Owner iRV2 No Limits Club
Join Date: Oct 2004
Posts: 30,785
|
If your FWS is flush and reveals both ends are equal your OK, if not you have to adjust the software explained here for the Newmar Slide System. KIB DUEL MOTOR CONTROL
|
|
|
06-22-2021, 10:27 PM
|
#9
|
Senior Member
Join Date: Sep 2010
Posts: 4,515
|
The torque should be 150 ft. lbs. The fact that it came lose would indicate that it wasn't torque enough.
Newmar Man
__________________
Tom/Teri 16031 NKK 117995 FMCA
18 London Aire 4531 Spartan K-3 605
97-04 LA 04-18 Essex 2018 London Aire
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|