|
05-06-2020, 08:29 PM
|
#1
|
Senior Member
Join Date: Aug 2016
Location: Redmond, WA
Posts: 188
|
2018 - Tail light surround became loose
Anyone else have this issue? The clips holding the tail light surround detached.
I'm going to try some super strong epoxy to re-attach them.
__________________
2018 Fleetwood Southwind 35K (aka Bounder LX) F53 22k
w/ CHF,Safe-T-Plus, UltraTrac Rear Trac Bar, Konis
+2013 Chevy Sonic LT hatch/Brake Buddy Stealth/BlueOx Alpha
|
|
|
|
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
05-07-2020, 12:09 AM
|
#2
|
Senior Member
Winnebago Owners Club Workhorse Chassis Owner
Join Date: May 2016
Location: Kamloops, BC, 60 miles from the Center of the Universe according to the Rinpoche, of the SF monks.
Posts: 7,387
|
Try some "Automotive Goop" works great.
Be sure to give it 24 hours to cure.
Happy Glamping.
__________________
Happy Glamping, Norman & Elna. 2008 Winnebago Adventurer 38J, W24, dozens of small thirsty ponies. Retired after 40 years wrenching on trucks! 2010 Ford Ranger toad with bicycles or KLR 650 in the back. Easy to spot an RVer, they always walk around with a screwdriver or wrench in one hand!
|
|
|
05-07-2020, 12:26 PM
|
#3
|
Junior Member
Join Date: Apr 2013
Posts: 15
|
I used JB Weld
Hello- We had this issue last year. I used JB Weld epxoy. I removed both covers and found all 4 clips were minimally attached. They are still holding strong.
__________________
Mark NM
2019 Bounder 35K
2015 Jeep Rubicon
|
|
|
05-07-2020, 02:36 PM
|
#4
|
Senior Member
Join Date: Jul 2010
Location: FT on the Road
Posts: 3,839
|
Yep, same on my 2016. Mine was replaced under warranty. Seems to be a common issue. I was told it needed to be replaced not repaired.
__________________
I don't subscribe to threads I reply to so will not see your reply to my comment. Drop me a direct message if you want a reply from me.
Cheers!
|
|
|
05-08-2020, 12:38 AM
|
#5
|
Senior Member
Join Date: Aug 2016
Location: Redmond, WA
Posts: 188
|
I used JB Weld 50139 Epoxy will see how it holds up - says it is good for metal-plastic truck bodywork bonding. I only left it a couple of hours to cure, hopefully it holds up.
https://www.amazon.com/gp/product/B01IBOK7FE/
I haven't looked at the right hand side -- it seems to be on fairly tight. I know they will come off if I mess with it.
__________________
2018 Fleetwood Southwind 35K (aka Bounder LX) F53 22k
w/ CHF,Safe-T-Plus, UltraTrac Rear Trac Bar, Konis
+2013 Chevy Sonic LT hatch/Brake Buddy Stealth/BlueOx Alpha
|
|
|
05-08-2020, 04:46 AM
|
#6
|
Senior Member
Join Date: Jan 2018
Posts: 105
|
Mine fell off on highway. Dealer put 2 screws in at the bottom on an angle right into the fiberglass body on both covers. Clips are worthless
|
|
|
12-19-2020, 01:44 PM
|
#7
|
Junior Member
Fleetwood Owners Club Ford Super Duty Owner
Join Date: Jul 2005
Location: Elgin, IL
Posts: 2
|
Hi guys, my first time on site.
I have a 2019 southwinf 37F.
How does one remove/,open the bezels,?
I have a tail light to replace and need to remove the bezel.
Thanks, phil
|
|
|
12-19-2020, 07:09 PM
|
#8
|
Senior Member
Join Date: Apr 2015
Location: Rogers, AR
Posts: 2,623
|
I would also try try the JB WELD, they have a formula just for plastics, got it at WalMart last week, about $7. Just clean the plastic good and on my test piece, it seems very good. You can also put some extra epoxy around the edges and build it up over the bottom edges of the clip making the adhesive area larger.
I might be corrected, but I think the JB WELD steel shown above is a very rigid, hard formula. The plastic formula is more pliable after cured, so it can slightly flex like plastic.
I haven't yet been disappointed in a JB WELD product.
__________________
2019 Fleetwood Discovery LXE 40M w/2021 Equinox
|
|
|
12-20-2020, 12:58 AM
|
#9
|
Senior Member
Join Date: Aug 2016
Location: Redmond, WA
Posts: 188
|
Quote:
Originally Posted by pfreyman
Hi guys, my first time on site.
I have a 2019 southwinf 37F.
How does one remove/,open the bezels,?
I have a tail light to replace and need to remove the bezel.
Thanks, phil
|
They pull out at the bottom, but most likely the glue will part ways and you'll wind up like in my photos.
__________________
2018 Fleetwood Southwind 35K (aka Bounder LX) F53 22k
w/ CHF,Safe-T-Plus, UltraTrac Rear Trac Bar, Konis
+2013 Chevy Sonic LT hatch/Brake Buddy Stealth/BlueOx Alpha
|
|
|
12-20-2020, 07:22 AM
|
#10
|
Junior Member
Fleetwood Owners Club Ford Super Duty Owner
Join Date: Jul 2005
Location: Elgin, IL
Posts: 2
|
Thanks, will give it a try when its warmer.
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|