|
04-08-2014, 08:41 AM
|
#1
|
Junior Member
Join Date: Sep 2013
Posts: 6
|
Access Panel Bolts
I'm trying to clean the screen on my lift pump and need to get access under the bedroom. I have a slide out. The book said to lift the carpet and remove the two bolts by the bed, or remove the carpet and remove the 5 bolts in the closet. Does anyone know where these bolts might be located? Is there a trick to lifting the carpet without pulling the nails/tacks holding it down?
|
|
|
|
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
04-08-2014, 09:21 AM
|
#2
|
Senior Member
Country Coach Owners Club
Join Date: Jan 2011
Posts: 1,204
|
year, model and length of your coach??????
|
|
|
04-08-2014, 09:38 AM
|
#3
|
Senior Member
Country Coach Owners Club
Join Date: Jan 2006
Location: Northern California
Posts: 5,868
|
On my rig, the bolts are covered by the carpet cut into flaps. If they are not visible, just pull up on the carpet edge in several places until you find the pattern.
__________________
Dean
1995 38' CC Magna #5280 **** Sold after 21 years of enjoyment.
|
|
|
04-08-2014, 09:43 AM
|
#4
|
Junior Member
Join Date: Sep 2013
Posts: 6
|
2004, Allure, Tag, 3 slides.
Carpet seems to be tacked down with these awful, sharp (cut my fingers) tacks or staples. I'm in the mood to pull them all out and start over just to see the bolts. Seems like this is the only option, though putting it all back together in a neat fashion might not be easy.
Thx for input.
Lar
|
|
|
04-08-2014, 11:14 AM
|
#5
|
Senior Member
Country Coach Owners Club
Join Date: Jan 2006
Location: Northern California
Posts: 5,868
|
On mine the bolts are at the four corners of the panel and in the middle of each side. 8 bolts in all.
__________________
Dean
1995 38' CC Magna #5280 **** Sold after 21 years of enjoyment.
|
|
|
04-08-2014, 12:18 PM
|
#6
|
Senior Member
Join Date: Nov 2009
Location: Warren, Oregon
Posts: 2,560
|
I just did mine to take it in for a valve adj. Mine had 6 bolts but I had to remove the mirros and the track on the floor. Take an pointed screwdriver and check for the heads. I opened the back door and looked up at the floor and could see the bolts. Cat shop just called they are done.
2 stroker
__________________
2006 Country Coach Inspire 360 40ft Genoa Designer Series, Samsung 197 RR
Cat C9--STEEL & COPPER Bolt Together Radiator w/ updated rubber mounting
SilverLeaf 330 Magnum 2812 PSW 2011 Ford Edge Sport-Air Force One
|
|
|
04-08-2014, 08:19 PM
|
#7
|
Senior Member
Join Date: Nov 2013
Location: Burien ,WA
Posts: 1,030
|
If you look at the floor from the engine compartment you can see the ends of the bolts. This will give you an idea. I don't know what coach you have so cannot comment any further.
|
|
|
04-09-2014, 06:05 AM
|
#8
|
Junior Member
Join Date: Sep 2013
Posts: 6
|
I see 6 bolts underneath, and it's pretty confusing now. The opening is square, but it goes right under the corner of the bed which is in the slide.
Somehow I'm figuring I'd have to remove the bed, frame and all, to get the square engine cover off.
I think after talking with my friend in Midland that I'm gonna leave the screen cleaning up to the shop. I guess that once on a lift, getting to the lift pump isn't that hard. My major problem is that I'll have to drive 100 miles to Saginaw to have it put on a dyno to figure out why I'm not getting power under load. I've had the turbo replaced, changed both fuel filters, and the air filter.
Thx for the response.
Lar
40' CC, tag, ISL 370, 3 slides.
|
|
|
04-09-2014, 05:36 PM
|
#9
|
Senior Member
Join Date: Dec 2007
Location: Anacortes, Wa.
Posts: 529
|
Again, depending on which model you have. You need to just lift the bed to get access. Also, must take closet doors off and door track. It can save a lot of time for the mechanic. $$$
__________________
John
08 Intrigue
2014 Ford Edge
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|