Community Forums

Mjmarlowe · 08-07-2022, 12:36 PM

New to me 07 Dynasty looking to be able to use the keyless entry. Does anyone know how to reset them

Thanks

jacwjames · 08-07-2022, 12:57 PM

Do you know keyless system you have.

Mine is a Essex. In my case there is a reset button hidden under/in the dash behind the radio. In my case it was a red button but enclosed in a piece of wire loom. I press the button and then program in a new entry code. See attached manual

I believe this is another brand that might have been used.

jacwjames · 08-07-2022, 12:58 PM

Here's the essex manual

96 Wideglide · 08-07-2022, 01:21 PM

Quote:

Originally Posted by jacwjames

Do you know keyless system you have.

I believe this is another brand that might have been used.

TriMark is the other manufacturer.

vito.a · 08-07-2022, 01:29 PM

I spent a lot of time learning the Trimark system on our 2007 Executive. I was able to purchase new generic remotes and program them.
Start reading at post #21:
https://www.irv2.com/forums/f115/hel...-324146-2.html

Mjmarlowe · 08-07-2022, 01:29 PM

It is a TRI mark

Mjmarlowe · 08-07-2022, 01:33 PM

Do you have the authority code

Carnac · 08-07-2022, 04:29 PM

On my 2003 Dynasty the reset button is under the passenger side cupholder (the one on the wall next to the passenger's seat.

If you have the same and need the instructions let me know and I can scan them for you.

Jim

ladyvol · 08-07-2022, 06:39 PM

We have the Essex keypad on our 2003 Monaco Dynasty. Original one was very small push buttons. We contacted Essex a few years ago and got the pad with the bigger numbers, enlarged the opening in the fiberglass and installed it. It works so much better than the original. Just sharing in case you are sick of trying to push the small buttons.

But here's my real issue that I'd like feedback about. A friend owns a 2004 Dynasty and can't get his keyless pad to work. We reprogrammed it for him and we know we did it right, but it still won't work.
In looking over his door we found he s missing one of the square push pins that are in the door frame and push in when the door closes.

Does anyone know what those pins are called? What they do? Are they in any way tied to the keypad? Is that possibly why his pad isn't working?

Thanks for any knowledge you have to share about the purpose of those square shaped "push pins"

Mjmarlowe · 08-08-2022, 10:18 AM

Didn’t see a button under the arm rest .. does anyone have the authority code? Thanks

vito.a · 08-08-2022, 12:39 PM

How to find the Trimark receiver: From an older thread: ronboc suggested setting the keyless entry system to lock, and then searching for the flashing red LED.

What a great idea! I locked the system using the keyless entry. You have to leave the door open to get back inside without unlocking. I went inside and shut off all the lights and searched for the flashing red light. Nothing in the passenger console. I had fiberglass rash on my hands and arms from searching it, so I was glad it wasn’t there.
I then searched through the center dash and nothing.

Next I laid on my back and searched the under dash area above the brake pedal. Way up high in the dash area I could see the reflection of a red flashing light. I could almost snake my arm up to it, but could not see the Trimark black receiver box (about the size of a cigarette pack). Then I looked on top of the dash and there was a removable panel held in by 2 screws. It is located about 12” in front of the speedo towards the windshield on the top of the dash. I removed that panel (it has 2 button covers over the screws and then the 2 screws) and the Trimark receiver was there under an AC duct. It is mounted to a steel cross bar.

Connected to it was the pushbutton and red LED still bundled up and secured with a wire tie.
Hope this helps.