|
02-07-2017, 11:05 AM
|
#1
|
Senior Member
Join Date: Aug 2016
Posts: 161
|
MCD shades help!!!
I am trying to adjust the cockpit MDC electric shades. These shades are controlled by a 6 switch Multiplex panel (not remote control). I have "All up" "All Down" and than a few like "Door" than one push will take it down and the next push will take it up.
Called MCD and got "Sorry don't know how to adjust these, Can help you with rocker switch or remote control systems, call Monaco" (really??? You manufacture these...)
Called Monaco and was told to use the "All up" and "All down" and a "rocker switch", put one shade into programing by shortening the learning wires and ignore all other shades while doing to programing.
I tried this method but it is not working right. The shade should beep and than go down until I leave the switch, however, it goes down about 6" and stops, from there on I can only "bump" it down 1/8" (like fine tune). Even doing this will not "lock" the down limit.
Any help??
__________________
2010 Dynasty Majestic V
|
|
|
|
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
02-07-2017, 04:20 PM
|
#2
|
Senior Member
Winnebago Owners Club Workhorse Chassis Owner
Join Date: May 2016
Location: Kamloops, BC, 60 miles from the Center of the Universe according to the Rinpoche, of the SF monks.
Posts: 7,387
|
Not sure if it will help you, but this is the way to set up and down limits on mine by RollerTrol RollerTrol? 12v DC Tubular Motor Instructions They are the ones that are not wireless controlled. Good luck.
__________________
Happy Glamping, Norman & Elna. 2008 Winnebago Adventurer 38J, W24, dozens of small thirsty ponies. Retired after 40 years wrenching on trucks! 2010 Ford Ranger toad with bicycles or KLR 650 in the back. Easy to spot an RVer, they always walk around with a screwdriver or wrench in one hand!
|
|
|
02-07-2017, 04:58 PM
|
#3
|
Senior Member
Join Date: Aug 2016
Posts: 161
|
Thanks Unplanned. The process I need help with relates to using the multiplex buttons since I don't have up/down buttons for each of the shades.
__________________
2010 Dynasty Majestic V
|
|
|
02-07-2017, 05:07 PM
|
#4
|
Senior Member
Country Coach Owners Club Solo Rvers Club iRV2 No Limits Club
Join Date: May 2011
Location: Vancouver, WA
Posts: 37,725
|
MCD made the shades but Monaco did the wiring and provided the switches. Why would MCD know how it was wired?
__________________
2009 45' Magna 630 w/Cummins ISX 650 HP/1950 Lbs Ft, HWH Active Air
Charter Good Sam Lifetime Member, FMCA,
RV'ing since 1957, NRA Benefactor Life, towing '21 Jeep JLU Rubicon Ecodiesel
|
|
|
02-07-2017, 05:15 PM
|
#5
|
Registered User
Join Date: Jul 2016
Posts: 299
|
Mine are also multiplex and here is how I set the MCD. Hold the learn button on the shade and have someone hold the multiplex down button. The shade should beep and start down, continue holding both buttons until the shade stops and beeps, then release multiplex first then the learn button. Then hold the multiplex down button until shade gets close to where you want it. You can then bump it down to where you want it. Reverse to up and again release up multiplex button when shade gets close to up. Bump it up to where you want it and then reverse to down which will take it out of programming mode. Ignore what the other shades do.
If yours don't have a learn button you can short the learn wires, but you have to hold each until the shade stops and beeps several times, then release multiplex button first.
|
|
|
02-07-2017, 05:23 PM
|
#6
|
Senior Member
Join Date: Aug 2016
Posts: 161
|
Got it solved. used this set of instructions but used the "all up" and "all down" to program each shade. You should not keep the program switch on all the time.
__________________
2010 Dynasty Majestic V
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|