Monaco emblem

[10Boomer]

Originally Posted by Notn2bars

We are looking for an emblem for our 2000 Dynasty. Our coach takes an emblem 4 1/4 by 5 7/8 to fit inside the oval. The emblem suggested is too large. Any info as to the correct emblem would be soooo appreciated. Thanks to all for your input.

PM me the one posted above isn’t the correct emblem.

[10Boomer]

Originally Posted by MSHappyCampers

Bob, are you sure that's what you paid for it? They are showing $40 now!

This emblem is for newer coaches and it’s the generator panel only. 2007- newer.
I searched site and called them. No cap emblems available.

[MSHappyCampers]

Originally Posted by 10Boomer

This emblem is for newer coaches and it’s the generator panel only. 2007- newer.
I searched site and called them. No cap emblems available.

My front emblem is on the generator panel. What's the difference?

[777 Driver]

When I owned my Monaco coach, I found Veurinks RV in Grand Rapids, MI to be helpful in locating Monaco specific parts. Here's a link to their online parts: https://shop.findmyrvparts.com/rv-pa...ries-s/100.htm Although I don't see the specific emblems that you're looking for in their online catalog, their process to submit a request for a specific part or a phone call to their customer service (616-965-9633) worked well.

I also had Allegiance RV in Wildwood, FL (352-232-7127) do some service several years ago and found some Monaco specific emblems (including the logo on the generator slideout) in their parts department.

Take care,
Stu

[10Boomer]

Originally Posted by MSHappyCampers

My front emblem is on the generator panel. What's the difference?

See my picture, cap Monaco emblems located on both front and rear drivers side caps and generator is located on genset door. Totally two different emblems.
Some coaches may have repainted and thus were removed and not reinstalled. Hope that helps.
[ATTACH]

[YC1]

I wish we could find someone to make them. Someone must know who made them for Monaco. The soft raised plastic ones on the sides are beautiful and keeping the appearance of these expensive toys up is worth a lot of money. I could see a couple of hundred dollars per side easily. Those little raised monoco logos that go on the wheels and last just a short time are not cheap but they really help keep things looking fresh.

[10Boomer]

Originally Posted by YC1

I wish we could find someone to make them. Someone must know who made them for Monaco. The soft raised plastic ones on the sides are beautiful and keeping the appearance of these expensive toys up is worth a lot of money. I could see a couple of hundred dollars per side easily. Those little raised monoco logos that go on the wheels and last just a short time are not cheap but they really help keep things looking fresh.

I know the original manufacture of the slightly raised front and rear cap emblems. Also know the original folks that did the name emblems for 2005-2010 coach model names.
Unfortunately they don’t manufacture them anymore. To set up again will cost into the thousands and have high production amounts.
One of those companies no longer are in business.

Something is brewing, PM me for information.

[777 Driver]

I'll admit that I know not much more than what I've seen on TV about 3D printing...but...this challenge sounds like it could well be solved by somebody (NOT ME) with the appropriate skills and a 3D printer.

Take care,
Stu

[Skipperh]

E-mail me rhainsworth@sbcglobal.net
On the generator door, there are at least 2 types. One is approximately 5 3/4 across which is made from a raised chrome plastic foam material. These usually get sun burned and fall apart or because of age they fall apart. Then there's the newer type, they are approximately 6 1/4 wide. I have tried to install the newer type on older coaches but to me they don't look right. The indentation on the door is to different. And as far as the front and rear cop emblems. I have found that the ones on the front are approximately 9 1/4 inches wide and on the rear they are approximately 10 1/2 inches wide. Some coaches came with the 9 1/4 wide on both ends. Or people have had the caps repainted and installed the 9 1/4 on the rear because the 10 1/2 weren't available. Through my searches neither one is available now. You can email me and I may have a solution.

[MSHappyCampers]

Originally Posted by Skipperh

E-mail me rhainsworth@sbcglobal.net

I sent you an e-mail.

[MSHappyCampers]

The emblem on my generator cap really looks bad and I would like to replace it. It looks like it is really stuck tight. Has anyone removed one of these, and if so, how did you do it?

[windsorbill]

Originally Posted by MSHappyCampers

The emblem on my generator cap really looks bad and I would like to replace it. It looks like it is really stuck tight. Has anyone removed one of these, and if so, how did you do it?

Joe,

I replaced a Ford emblem on my truck a few years ago. I took a piece of fishing line and got it behind the emblem. sawing it back and forth, it came right off.

[MSHappyCampers]

Originally Posted by windsorbill

Joe,

I replaced a Ford emblem on my truck a few years ago. I took a piece of fishing line and got it behind the emblem. sawing it back and forth, it came right off.

Thanks Bill! I would never have thought about that trick!

[Skipperh]

MSHappycampers, I never received your email.