Community Forums

slrv · 07-29-2014, 04:13 PM

Quote:

Originally Posted by DieselTech39

Photos didn't show. Got to be in *.jpg format I think.

LOL no they didn't let me try this

DieselTech39 · 07-29-2014, 04:29 PM

In the reply window click on the paper clip and choose the photo file to add.

slrv · 07-29-2014, 04:37 PM

I think it worked this time LOL

TQ60 · 07-29-2014, 04:49 PM

Looks like potted in and many relays and what looks like atx fuses.

You sure it is bad?

Do you have troubleshooting procedure from manufacturer?

Is this engine control or chassis control?

TQ60 · 07-29-2014, 04:51 PM

Looked at second photo so body control.

Just relays and fuses with whatever controls relays.

Is it totally dead or does anything work?

slrv · 07-29-2014, 04:53 PM

Quote:

Originally Posted by TQ60

Looks like potted in and many relays and what looks like atx fuses.

You sure it is bad?

Do you have troubleshooting procedure from manufacturer?

Is this engine control or chassis control?

We have taken the back off the module and it is burnt and melted in 1 part.

This part is the Chassis Control Module

TQ60 · 07-29-2014, 05:03 PM

If melted then something like a fuse did not...

You may be able to get a diagram or schematic from beaver that may help.

If still intact it may be repairable...restored water damaged ckt boards back in the day and it is not that hard if you have documentation.

It looks like a coach builder part but beaver may have outsourced it.

You may needcto google part numbers and descriptions and maybe you might find a vendor or servicer.

ImagineIF · 07-29-2014, 05:08 PM

If you haven't tried the Beaver Club, you might want to http://beaveramb.org It looks like a relay control box that can likely be replaced with common parts. Your challenge may be getting the wiring diagrams.

TQ60 · 07-29-2014, 05:16 PM

Lots of megatech companies from radio control to game systems.

But there is one that does control systems but maybe still not it.

Part numbers no good.

It is less than 10 years old so there should have been stock someplace but companies changing could make that go away.

bruceisla · 07-29-2014, 05:29 PM

Can we see some pictures of the back of the board with components exposed?

Also, what is the failure symptom? I.E. won't start/trans won't engage/no electrical power anywhere/etc.

From the front picture the module doesn't look very complex. It just looks like a board they hung relays and fuses on.

deandec · 07-30-2014, 11:38 AM

Had a similar problem with a printed circuit board several years ago that was coach specific made by a local business now out of business.

Once I had pictures of the board and its components several folks on this forum were able to guide me through the diagnosis and replacement of parts.

So, post the pictures of the back side of your component. Lots of expertise here.

DieselTech39 · 07-30-2014, 03:03 PM

Sent you a couple of PMs (Personal Mails) on your CCM. Please check them out if you would.

slrv · 07-30-2014, 03:35 PM

Quote:

Originally Posted by bruceisla

Can we see some pictures of the back of the board with components exposed?

Also, what is the failure symptom? I.E. won't start/trans won't engage/no electrical power anywhere/etc.

From the front picture the module doesn't look very complex. It just looks like a board they hung relays and fuses on.

Here are some pictures for you, The complaint was that some of the dash lights where not working and that the steering wheel functions are not working. No Cruise control, no windshield wipers, no day time running light.

cold_one · 08-15-2014, 06:52 AM

You should also post your problem on the Beaver forum. May get the same answers but a lot of experience there that might help.

BAC Forum - BAC Forum

They have helped me a number of times