 |
05-31-2023, 01:53 PM
|
#1
|
|
Junior Member
Monaco Owners Club
Join Date: Mar 2022
Posts: 16
|
cruise control
2006 endeavor cruise control fuse, it worked when i parked it fall, now it doesn't.
|
|
|
 |
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
|
05-31-2023, 01:57 PM
|
#2
|
|
Senior Member
Join Date: Apr 2011
Location: Powell River, B.C.
Posts: 30,496
|
What chassis is your coach built on ?
For those of us who don't know all the chassis/motorhome combinations . 
__________________
99DSDP 3884, Freightliner, XC, CAT 3126B, 300 HP /ALLISON 3060
2000 Caravan toad, Remco & Blue Ox.
|
|
|
|
|
05-31-2023, 02:23 PM
|
#3
|
|
Senior Member
Monaco Owners Club
Join Date: Jun 2014
Posts: 13,716
|
Do you have a VIP smartwheel?? (the fancy wheel with all the buttons).
If so the cruise is controlled by the Smartwheel controller.
I checked my fuses and do not have one specifically for cruise control BUT there is some circuits that interact with the smartwheel system. The brake circuit is what sends a signal to the smartwheel controller for cruise cancel so check any fuse that has something to do with the brake. The engine brake also interacts with the cruise, it won't come on if cruise is on, I have to tap my brakes to get cancel cruise before Pacbrake comes on.
__________________
Jim J
2002 Monaco Windsor 38 PKD Cummins ISC 350 8.3L
2005 Jeep Grand Cherokee w/5.7 Hemi
|
|
|
|
|
06-01-2023, 10:24 AM
|
#4
|
|
Junior Member
Monaco Owners Club
Join Date: Mar 2022
Posts: 16
|
Roadmaster RR8R*
|
|
|
|
|
06-01-2023, 10:28 AM
|
#5
|
|
Junior Member
Monaco Owners Club
Join Date: Mar 2022
Posts: 16
|
yes it has smart wheel. would the engine brake keep it from working?
|
|
|
|
|
06-02-2023, 04:51 AM
|
#6
|
|
Senior Member
Holiday Rambler Owners Club
Join Date: Apr 2020
Location: Farmington Hills, Michigan
Posts: 891
|
Quote:
Originally Posted by wayne67
yes it has smart wheel. would the engine brake keep it from working?
|
On my HR, the cruise won't engage if the engine brake is on.
__________________
2004 Holiday Rambler Imperial 40PKD, Cummins ISL 400
2019 Buick Envision AWD
|
|
|
|
06-03-2023, 11:24 AM
|
#7
|
|
Senior Member
Join Date: Oct 2017
Posts: 297
|
I have found that with Diesel Pushers the cruise control (CC) is function of the engine (CAT or Cummings) ECM. The CC on my CAT quit working and there was no “Fuse” because the CC is a function of the ECM. The “brake light” switches are operated by the air brakes pressures and not switch a on the “brake pedal” like a car. The CC pressure switch is a “Normally Closed” switch that opens when the pressure is above 3PSI. So the CC brake input was grounded until the brake pressure exceeded 3PSI then CC dropped out.
While troubleshooting my problem I found the fast idle did not work. After reviewing the schematics and tracing the wire colors/strip I was able to find the correct pressure switch. There were three “Brake” pressure switches on panel in the front run bay. I was able separate the CC switch from the brake light switches. I found the CC switch contacts were open with no brake pressure and did not change state when the brakes were applied. I jumpered across the CC pressure switch contacts and the fast idle worked. Took a test drive and the CC was working.
If all the other Smart Wheel function work I would check the CC pressure switch. Not sure about the Engine brake, as my CAT JAKE Brake does not effect the CC function. It could also be a function of ECM programming. Did the Engine brake effect the CC before it quit working?
__________________
Country Coach 2000 MAGNA C10
|
|
|
|
|
06-03-2023, 11:41 AM
|
#8
|
|
Senior Member
Monaco Owners Club Freightliner Owners Club Holiday Rambler Owners Club
Join Date: Sep 2019
Location: Thornville, Ohio
Posts: 3,406
|
Quote:
Originally Posted by Lowflyer1
On my HR, the cruise won't engage if the engine brake is on.
|
On my HR endevor cruse will work with engine brake set on. But as soon as it engages it will turn off the same as applying the air brakes.
|
|
|
|
|
06-04-2023, 01:08 PM
|
#9
|
|
Junior Member
Monaco Owners Club
Join Date: Mar 2022
Posts: 16
|
cruise doesn't work with engine brake on. Boy do i feel stupid!!!
|
|
|
|
|
06-04-2023, 01:13 PM
|
#10
|
|
Senior Member
Join Date: Mar 2019
Posts: 1,638
|
Quote:
Originally Posted by wayne67
cruise doesn't work with engine brake on. Boy do i feel stupid!!!
|
Don't feel stupid. It is only dumb if you do it again.
|
|
|
|
|
06-04-2023, 01:49 PM
|
#11
|
|
Senior Member
Monaco Owners Club
Join Date: Jun 2014
Posts: 13,716
|
If I were paid $1 for every stupid thing I did I'd be richer then I am now.
Glad you got it fixed.
__________________
Jim J
2002 Monaco Windsor 38 PKD Cummins ISC 350 8.3L
2005 Jeep Grand Cherokee w/5.7 Hemi
|
|
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
|
| Thread Tools |
Search this Thread |
|
|
|
| Display Modes |
 Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
