RV News RVBusiness 2021 Top 10 RVs of the Year, plus 56 additional debuts and must-see units → ×
RV Trip Planning Discussions

Go Back   iRV2 Forums > MOTORHOME FORUMS > Class A Motorhome Discussions
Click Here to Login
Join iRV2 Today

Mission Statement: Supporting thoughtful exchange of knowledge, values and experience among RV enthusiasts.
  This discussion is proudly sponsored by:
Please support our sponsors and let them know you heard about their products on iRV2
Thread Tools Search this Thread Display Modes
Old 07-17-2017, 10:02 PM   #1
Join Date: Apr 2014
Posts: 45
Sagging full wall slide out

I have a 2012 Itasca Suncruiser 35P with a full wall power gear slide out (slide out is about 30’ long).

The slide out moves in and out without problems, but I noticed when closed, that the front sits about ˝ inch lower than normal, and the rear is slightly higher.

Like I said, it moves fine, and seals perfect when closed. What holds it in place, does it run on rollers? Because is works fine, I wonder if something broke or needs adjusting. As far as I can tell, the power gear just moves it in and out and doesn’t carry the weight.

Any suggestions appreciated
2012 Itasca Suncruiser 35P
2002 Volkswagen Beetle on a eze-tow dolly
RndmTraveler is offline   Reply With Quote
Join the #1 RV Forum Today - It's Totally Free!

iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!

You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!

Old 07-18-2017, 02:31 AM   #2
"Formerly Diplomat Don"
Dutch Star Don's Avatar
Newmar Owners Club
Join Date: Apr 2005
Location: Moorpark, Ca.
Posts: 16,311
On most slides, if you extend it and look under the outer edge, you should see two, maybe three threaded bolts, sitting vertically just inside the exterior wall of the slide. They're usually double nutted. These adjust the slide on the slide frame. You loosen the double nuts and turn the threaded bolt until you gain about a 1/4". Lower the rear a 1/4", bring the slide in and check the fit. You may have to do this a couple of times.
Don & Mary
2019 Newmar Dutch Star 4018 (Freightliner)
2019 Ford Raptor
Dutch Star Don is offline   Reply With Quote
Old 07-19-2017, 11:15 AM   #3
Join Date: Apr 2014
Posts: 45
Found the problem...i think

one of the bolts on the center support bracket broke. Don't know yet if I can replace it myself, or have to take it to the dealer.
2012 Itasca Suncruiser 35P
2002 Volkswagen Beetle on a eze-tow dolly
RndmTraveler is offline   Reply With Quote

slide, slide out

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
Sagging Full Wall Slide Winepress Class A Motorhome Discussions 3 09-14-2014 09:44 AM
Sagging slide-out topper awnings on 04 Monaco Monarch Jim Stout Monaco Owner's Forum 2 08-04-2014 09:18 AM
Full wall slide will not full retract corjaguar Winnebago Industries Owner's Forum 27 04-05-2014 03:51 AM
Lance wont warranty sagging wall defects cummins nut Truck Camper Discussion 4 02-12-2006 06:47 AM

All times are GMT -6. The time now is 08:20 AM.

Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2020, vBulletin Solutions, Inc.