|
|
08-08-2018, 04:38 PM
|
#1
|
Junior Member
Entegra Owners Club Spartan Chassis
Join Date: Aug 2017
Posts: 26
|
Anthem Bed Slide Won't Retract
The bed slide on our Anthem 42 DEQ won't retract. All the others are fine. When you try the retract on the light panel for the Bed Side in the bedroom there is nothing in either the open or retract. The other slide works fine. The panel in the bathroom indicates a green light for that fuse when you press the retract button.
Is there a manual way to retract the slide?
__________________
Buzz & Robin
2019 Entegra Qwest 24-L
2000 Jeep TJ
|
|
|
|
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
08-08-2018, 04:58 PM
|
#2
|
Registered User
Join Date: May 2017
Posts: 2,582
|
Quote:
Originally Posted by bremde
The bed slide on our Anthem 42 DEQ won't retract. All the others are fine. When you try the retract on the light panel for the Bed Side in the bedroom there is nothing in either the open or retract. The other slide works fine. The panel in the bathroom indicates a green light for that fuse when you press the retract button.
Is there a manual way to retract the slide?
|
The controllers for the slides are in the first compartment d/s. I had wire come off on a 14 Anthem. Also you can swap wiring to one of the other controllers if the controller is the problem.
As far as manual retracting you would have to disconnect the drive, push it in and reconnect the drive so brake in motor would hold the slide in. I would definitely check the controllers first.
|
|
|
08-08-2018, 05:18 PM
|
#3
|
Senior Member
Entegra Owners Club
Join Date: Apr 2007
Location: SW FL
Posts: 31,622
|
Try turning off 12v power and see if it will reboot the switch system. The switches are located at the entrance door and the drivers console.
__________________
Chuck in SW FL
Digital 2021 Cornerstone "B"
A "Digital" 2019 Cornerstone "B" Traded
A "Classic" 2014 Anthem 42 RBQ---Sold
|
|
|
08-08-2018, 05:48 PM
|
#4
|
Junior Member
Entegra Owners Club Spartan Chassis
Join Date: Aug 2017
Posts: 26
|
Okay, I have looked at the controllers in the DS Bay. When we try all of the slides, there is a click. The only one that doesn't;t register a light is the bed slide which is the problem slide.
I have re-set the 12V by shutting off the Battery connect at the door, waited a few minutes then turned it back on.
Still nothing from the naughty slide. the others are working fine.
__________________
Buzz & Robin
2019 Entegra Qwest 24-L
2000 Jeep TJ
|
|
|
08-08-2018, 05:52 PM
|
#5
|
Junior Member
Entegra Owners Club Spartan Chassis
Join Date: Aug 2017
Posts: 26
|
Let me clarify. When I look at the controllers in the Bay. I try each of the slides that are working and there is a green light and a click and they start to work. When I look at the controller in the Bay and try the bad slide, there is a click but no green light and it doesn't;t work.
__________________
Buzz & Robin
2019 Entegra Qwest 24-L
2000 Jeep TJ
|
|
|
08-08-2018, 05:54 PM
|
#6
|
Junior Member
Entegra Owners Club Spartan Chassis
Join Date: Aug 2017
Posts: 26
|
The motor shaft beneath the bed does not move. I have tried to move the shaft to release the pressure on the shear pins but to no avail.
__________________
Buzz & Robin
2019 Entegra Qwest 24-L
2000 Jeep TJ
|
|
|
08-08-2018, 05:55 PM
|
#7
|
Junior Member
Entegra Owners Club Spartan Chassis
Join Date: Aug 2017
Posts: 26
|
Would it be safe to un-bolt the motor from the bed frame?
__________________
Buzz & Robin
2019 Entegra Qwest 24-L
2000 Jeep TJ
|
|
|
08-08-2018, 06:10 PM
|
#8
|
Senior Member
Join Date: Nov 2011
Location: Florida
Posts: 1,454
|
Switch the wires on the controller from one of the slides that does work then use that switch to retract the slide(ie switch the wires between the vanity slide controller and the bed slide controller then press the vanity slide retract button to retract bed slide)
|
|
|
08-08-2018, 06:15 PM
|
#9
|
Registered User
Join Date: May 2017
Posts: 2,582
|
Quote:
Originally Posted by fla tom
Switch the wires on the controller from one of the slides that does work then use that switch to retract the slide(ie switch the wires between the vanity slide controller and the bed slide controller then press the vanity slide retract button to retract bed slide)
|
X2.
|
|
|
08-08-2018, 06:26 PM
|
#10
|
Junior Member
Join Date: Jun 2015
Posts: 9
|
DW here... sadly, the wires are EXACTLY as long as they need to be - don't reach to the other 3. Would you suggest a small jumper from a couple of small alligator clips?
|
|
|
08-08-2018, 06:28 PM
|
#11
|
Registered User
Join Date: May 2017
Posts: 2,582
|
Quote:
Originally Posted by rremde
DW here... sadly, the wires are EXACTLY as long as they need to be - don't reach to the other 3. Would you suggest a small jumper from a couple of small alligator clips?
|
Yes or swap controllers.
|
|
|
08-08-2018, 07:00 PM
|
#12
|
Junior Member
Join Date: Jun 2015
Posts: 9
|
First, thank you for all the assistance, and tolerance of newbie questions.
Are the controllers the black cubes on the board, and should they pull out?
|
|
|
08-08-2018, 07:11 PM
|
#13
|
Senior Member
Entegra Owners Club
Join Date: Jan 2015
Location: Caldwell , Ohio 43724
Posts: 1,443
|
Don't know if noticed but that green wire is disconnected from it's terminal. Perhaps you disconnected it chasing the problem.
Richard
__________________
Gasman 2
2016 Anthem 42 RBQ Sold June 2021
Toad 2017 GMC Sierra 4X4
|
|
|
08-08-2018, 07:49 PM
|
#14
|
Senior Member
Join Date: Nov 2014
Location: Niceville, Florida
Posts: 773
|
I would pull and visually check that 40amp automotive style fuse that is on the bed slide corner of your control board. I believe that is on the retract side of your slide
__________________
2012 Entegra Aspire RBQ
2009 Chevy Z71 Tahoe Four Down
2019 GMC Sierra 1500 Four Down
|
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|