Tell others about your modifications

[Aangulo1]

Love this mod Rod!!!!

Would it be much to ask to share the amazon links for the redt of the hardware? Switches, lights, enclosure, fuse unit, etc!!

What is the upper left unit in your diagram? Is that the fuse unit you installed where the master switch is connected to?

What's the REV SW and FWD SW mentioned in the diagram, Is this hardware as well?

Sorry for so many questions.


Loved it!

[rlwhite]

Abe,
It looks like Amazon is currently out of the Barker 24130 Auto-Drain 3" Valve but can be purchased from others. This comes with the open/close momentary switch with light indicator. If you want to stay with just the manual approach, switches inside and in the wet bay, and not install the Shelly's, you will need a 6 pin dpdt switch in between. This would have to be used to activate either the inside switch or the outside switch. I've attached the drawing on how to do that.

Yes, the upper unit in the drawing is the fuse panel. The kill switch is wired in between the supply power and the fuse panel.
The Rev Switch/Forward Switch is the OONO box.

If you want the snazzy version you will need the following:
1) Qty 2, OONO Forward and Reverse Relay... https://www.amazon.com/dp/B0879GGVPZ...p_mob_ap_share

2) 12 Volt Fuse Block, Waterproof 6... https://www.amazon.com/dp/B09NVJT1R9...p_mob_ap_share

3) 1/4" Stud & 12 x #8 Terminal (to extend ground buss bar)... https://www.amazon.com/dp/B09T6NBTD5...p_mob_ap_share

4) Qty 2, True Mods 1-Slot Rocker Switch (for wet bay)... https://www.amazon.com/dp/B07CNC59CX...p_mob_ap_share

5) Qty 4, BANDC Waterproof Momentary Rocker... https://www.amazon.com/dp/B0CNS17ZMK...p_mob_ap_share

6) Qty 2, Alpinetech PLB12M 12mm 1/2" 12V... https://www.amazon.com/dp/B072BBM1R2...p_mob_ap_share

7) Qty 1, True Mods 2-Slot Rocker Switch (for inside)... https://www.amazon.com/dp/B06XB6338J...p_mob_ap_share

8) Qty 2, Shelly Plus Uni | Smart Wi-Fi and... https://www.amazon.com/dp/B0CQD1Z2K8...p_mob_ap_share

9) Qty 1 (5 pack), ABS Plastic Project Boxes for... https://www.amazon.com/dp/B0CG1LZ7SK...p_mob_ap_share

10) Qty 1, Jienk 300V 10A 5.08mm Pitch PCB... https://www.amazon.com/dp/B09TKFHZV9...p_mob_ap_share

11) Qty 1, Jienk 2Pack 10-Pin 300V 10A... https://www.amazon.com/dp/B09KKS15JY...p_mob_ap_share

12) Qty 1, RVMARINEPAT Toggle Switch 12V DC... https://www.amazon.com/dp/B0CZ8M3SQ9...p_mob_ap_share

13) Qty 1, 18 Gauge Wire 2 Conductor... https://www.amazon.com/dp/B0BGS6CGV3...p_mob_ap_share

14) Qty 1, Order the length you need ( will need to pull 2 4wire inside, one 4 wire for each switch and indicator light) Gonice 25Ft 4 Pin Trailer Wiring... https://www.amazon.com/dp/B0BQM6YMMS...p_mob_ap_share

If you would like to discuss further, private message me with your phone number.

[Aangulo1]

Thanks Rob for the info!!

So with regards to the Barker. We need one for each tank. The 24130 is a 3 inch for the black, the grey has a smaller diameter right? Do we need the 24140 for it?

Thanks again!!

[rlwhite]

Originally Posted by Aangulo1

Thanks Rob for the info!!

So with regards to the Barker. We need one for each tank. The 24130 is a 3 inch for the black, the grey has a smaller diameter right? Do we need the 24140 for it?

Thanks again!!

Abe,
Yes, you need a Barker drain motor for each tank. Not sure how the 2013 is setup. I would expect both the black and grey tank valves are 3" but you need to verify.

[voltdoc]

Originally Posted by rlwhite

Abe,
Yes, you need a Barker drain motor for each tank. Not sure how the 2013 is setup. I would expect both the black and grey tank valves are 3" but you need to verify.

My '13 had 3" valves for both tanks. As far as I know, all Entegra Aspire/Anthem/Cornerstone do.
Photo: https://photos.app.goo.gl/AHRfPq3cHusvVuQC6

[Aangulo1]

Originally Posted by voltdoc

My '13 had 3" valves for both tanks. As far as I know, all Entegra Aspire/Anthem/Cornerstone do.
Photo: https://photos.app.goo.gl/AHRfPq3cHusvVuQC6

Thanks Rob. You are correct.