|
05-03-2022, 08:17 AM
|
#1
|
Junior Member
Join Date: Aug 2019
Location: Tolland, Ct
Posts: 3
|
12 v issue Brook Side 2006
Hi, I’ve a 2006 Brook Side 5th.
12 v systems works when on shore power. Not work when disconnected to shore.
Batteries v 25.9. In series. So charged. Converter then seems to work.
Main panel breakers turned on-off several times.
LOW POWER PANEL, bayonet fuses resist removal. There is a ¨Plunger¨ type device on the outside of the panel box. It resists moving. It is part of a rectangular segment inside.
I could use W40D to spray all fuses and the plunger.
|
|
|
|
Join the #1 RV Forum Today - It's Totally Free!
iRV2.com RV Community - Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you'll find that iRV2 is a great community to join. Best of all it's totally FREE!
You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners, see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
|
05-03-2022, 08:59 AM
|
#2
|
Senior Member
Damon Owners Club
Join Date: Apr 2020
Location: Clovis NM
Posts: 4,389
|
While I can't help you with your issue, I would not suggest spraying fuses with WD40, I don't know if it's conductive, but I doubt it would help. Your fuse panel is designed to keep the fuses in place, so, it's not surprising they are hard to remove. I usually use a needle nose pliers to pull them. Sounds like power is not getting from battery bank to fuse block. Have you looked at your battery isolator/disconnect solenoid yet? Grab a meter and check both sides of the disconnect solenoid, should have full battery power on both sides.
__________________
2006 Damon Daybreak 3276 35'with 5 Star Tuner. 3 200 Amp Lithium batteries and 2000 watt PSW inverter/charger. 2013 Elantra on a Master Tow dolly.
Retired USAF
|
|
|
05-03-2022, 09:01 AM
|
#3
|
Senior Member
Join Date: Apr 2011
Location: Powell River, B.C.
Posts: 31,495
|
Quote:
Originally Posted by Peter’s Brook
Hi, I’ve a 2006 Brook Side 5th.
12 v systems works when on shore power. Not work when disconnected to shore.
Batteries v 25.9. In series. So charged. Converter then seems to work.
|
Ok , I'm confused by this statement .
Batteries v 25.9. in series .
Do you have 2 six volt batteries in series ; that only showed 5.9 volts when tested ?
__________________
99DSDP 3884, Freightliner, XC, CAT 3126B, 300 HP /ALLISON 3060
2000 Caravan toad, Remco & Blue Ox.
|
|
|
05-03-2022, 09:20 AM
|
#4
|
Community Moderator
Join Date: Aug 2018
Location: Full timing
Posts: 6,345
|
Quote:
Originally Posted by Peter’s Brook
Hi, I’ve a 2006 Brook Side 5th.
12 v systems works when on shore power. Not work when disconnected to shore.
Batteries v 25.9. In series. So charged. Converter then seems to work.
Main panel breakers turned on-off several times.
LOW POWER PANEL, bayonet fuses resist removal. There is a ¨Plunger¨ type device on the outside of the panel box. It resists moving. It is part of a rectangular segment inside.
I could use W40D to spray all fuses and the plunger.
|
Batteries hooked in series 6volt or 12 volt? If with 12 volt batteries hook them in parallel.
__________________
2018 Road Warrior 427
2013 Can Am Spyder RT Limited
2017 Ram 3500 w/Aisin w/4:10
2 Dachshunds DJ (RIP 9-12-19) & Joey (RIP 5-14-21)
|
|
|
05-03-2022, 09:28 AM
|
#5
|
Senior Member
Join Date: Jul 2014
Posts: 35,443
|
Connect batteries in parallel so that you have 12 volts and then find the fuse or breaker near the battery that hopefully blew.
Things working on shore power means the converter is working, that's good, but don't send 24 volts to it.
|
|
|
05-06-2022, 09:25 AM
|
#6
|
Junior Member
Join Date: Jan 2021
Location: Fulltimer
Posts: 10
|
Had same issue with our 1st 2006 Brookside.
Look for circuit breaker. click here for image don't remember where its located.
Little black button...pushed it in, got a nice click, and presto........the 12V system is working again.
__________________
2015 RAM LongHorn 3500 Dually 4X4 CUMMINS/AISIN
2013 Lifestyle LS35SB, MORryde IS System, disc brakes
AIRSAFE Air Hitch
|
|
|
05-07-2022, 10:23 AM
|
#7
|
Community Moderator
Join Date: Aug 2018
Location: Full timing
Posts: 6,345
|
Quote:
Originally Posted by Peter’s Brook
Hi, I’ve a 2006 Brook Side 5th.
12 v systems works when on shore power. Not work when disconnected to shore.
Batteries v 25.9. In series. So charged. Converter then seems to work.
Main panel breakers turned on-off several times.
LOW POWER PANEL, bayonet fuses resist removal. There is a ¨Plunger¨ type device on the outside of the panel box. It resists moving. It is part of a rectangular segment inside.
I could use W40D to spray all fuses and the plunger.
|
Any update yet?
__________________
2018 Road Warrior 427
2013 Can Am Spyder RT Limited
2017 Ram 3500 w/Aisin w/4:10
2 Dachshunds DJ (RIP 9-12-19) & Joey (RIP 5-14-21)
|
|
|
05-08-2022, 05:00 AM
|
#8
|
Junior Member
Join Date: Aug 2019
Location: Tolland, Ct
Posts: 3
|
12 v issue 2006 brook Side
Thanks to all.
Problem solved. Weak cells in both deep cycle batteries- But was able to charge them using a charger plus shore-converter power. Will replace them upon arrival home in at week.
Batteries are in parallel.
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|