iRV2 Forums

iRV2 Forums (https://www.irv2.com/forums/)
-   Fleetwood Owner's Forum (https://www.irv2.com/forums/f107/)
-   -   Pace Arrow: PACE ARROW owners group (https://www.irv2.com/forums/f107/pace-arrow-owners-group-393245.html)

donnyman 08-28-2021 09:53 AM

info
 
Hello


I suggest you start with Fleetwood, they will supply you with much info if they have it.

Some help can be had on line from various forums, "you tube" is loaded with info.

Searching your particular unit here and on the internet will yield much info but be prepared that most people will say they did something but have no explanation of how and rarely have pictures. The information is out there but has to be hunted down. remember the differences from year to year on these units can vary.

I have found the best thing is to be specific on this site as to what you wish to work on and someone has already done it and will respond (good luck)

I have a lot of info and will share it with you but you must be specific.

seatec70 10-15-2021 02:59 PM

Hello folks
2006 Pace Arrow 37c ford chassis
Dealer installed a valve for the city water/bypass tank fill. When it turn the. Valve to bypass so not to fill the water tank I still get a little water going into the water tank. Enough so I have to open the dump valve underneath so the tank won't fill up. Is this a bad valve or could something else be faulty

Thank you

BarbPrueitt 11-01-2021 07:42 PM

2006 Pace arrow 37c replaced flooring
 
I just purchased a 37C that they had redone the flooring and put in a super cheap home depot brand composite floor. I think it was a home decorator's brand. It was super thin and the slide still rubs on it and scratches it. Plus it was done a little over 1 year ago and there are gaps in the flooring. So annoying. I am thinking I am going to have to replace it with vinyl. Does anyone have any thoughts?? I would attach a photo but I can't figure out how to do that. the photo is on my laptop note on the web.

donnyman 11-02-2021 08:25 AM

Quote:

Originally Posted by BarbPrueitt (Post 5971540)
I just purchased a 37C that they had redone the flooring and put in a super cheap home depot brand composite floor. I think it was a home decorator's brand. It was super thin and the slide still rubs on it and scratches it. Plus it was done a little over 1 year ago and there are gaps in the flooring. So annoying. I am thinking I am going to have to replace it with vinyl. Does anyone have any thoughts?? I would attach a photo but I can't figure out how to do that. the photo is on my laptop note on the web.


I do not have the answers you seek but permit me to say ... If the present flooring is damaged by your slide now any new flooring will get the same damage unless you have what is causing the damage repaired ................... Good luck!

MrsChilerick 11-02-2021 08:37 AM

I agree with donnyman. But, also recommend what I think the techs at REV call “slide glides”. They are plastic on one side and carpet on the other and you place them on the floor where the the slide rollers roll over the the floor when you bring in the slide. They work quite well.

rschley 11-03-2021 08:25 PM

I have a Pace Arrow 2002. The Service Engine Soon light came on. I can’t find the OBD 2 plug so as to run diagnostics on the engine. Where can I find it?

Also, what do I push to get the big horn on the roof work? Would love to use it.

Thanks!!

rschley

Lakeman1 11-03-2021 09:23 PM

Quote:

Originally Posted by MrsChilerick (Post 5972007)
I agree with donnyman. But, also recommend what I think the techs at REV call “slide glides”. They are plastic on one side and carpet on the other and you place them on the floor where the the slide rollers roll over the the floor when you bring in the slide. They work quite well.

Yes that is what is needed, the slides DON'T have rollers. They have nylon slides that slid on the carpet. The "slide guide" will fix your problem and cover up the scratches,

Flyer15015 11-06-2021 04:03 PM

Quote:

Originally Posted by rschley (Post 5973878)
I have a Pace Arrow 2002. The Service Engine Soon light came on. I can’t find the OBD 2 plug so as to run diagnostics on the engine. Where can I find it?

Also, what do I push to get the big horn on the roof work? Would love to use it.

Thanks!!

rschley

The port on my '04 Pace Arrow is down under the dash, to the left of the steering column. Kind of hidden down there.

Mike in Colorado

Manny G 11-08-2021 03:09 PM

I have a 2004 Pace arrow 37c. Does anyone know where I can find a Windshield center support. REV parts is about 6 weeks out and I've tried the salvage yard. Part #10081397. Its 50.1 " long

tropical36 11-08-2021 05:56 PM

Quote:

Originally Posted by Manny G (Post 5978878)
I have a 2004 Pace arrow 37c. Does anyone know where I can find a Windshield center support. REV parts is about 6 weeks out and I've tried the salvage yard. Part #10081397. Its 50.1 " long

Have you tried Colaw Salvage as well?

Manny G 11-09-2021 12:58 PM

Yes I tried Colaw and Visone

ColoradJayco 11-25-2021 03:13 PM

Persistent problems
 
We have a 2019 38K PA with the Freightliner chassis. The house batteries have always been troublesome. The 12v circuits won't come on, after running the generator, lights and slides the day before. I know one 6v battery had a bad cell, so I replaced that pair with new Interstate GC2s from Costco. I charged the new pair and the remaining pair with the "smart" trickle charger, but the house circuits still won't come on. I have cycled the breakers, reconnected everything correctly (took photos of every battery post). What am I missing? Does the inverter need to be on for the 12v? The fridge works, the electric plugs work, the charging monitors with a 30 amp generator working start Loading, then Floating...where have my house circuits gone?

RKyzar 12-03-2021 11:34 AM

Super Slide Topper Issues
 
I bought new 2017 Pace Arrow LXE 38B. Have had more than our share of issues but have gotten most of them resolved. However one Issue that we still have is the Super Slide Topper staying taught. I have had it back to dealer 3 times to repair with the same results. I was told by the dealer that this was my fault and not a mfg warranty issue due to leaving the slide out for a extended time (not the case). Dose anyone have recommendations on a solution to keep the topper taught?
Thanks

jaearhart 12-04-2021 09:40 AM

I have the 2018 38B with drivers side slide and one long passenger side slide . I've never experienced a Taught topper. Id suspect its not initially set up correctly . You can you tube and see several good pointers to adjust it.


All times are GMT -6. The time now is 07:01 AM.

Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2022, vBulletin Solutions, Inc.